What to do if Ricoh PJ X6180N Projector lamp does not light?
If the lamp in your Ricoh Projector does not light, wait at least 1 minute, then turn the power back on. If the lamp still does not light, contact your dealer.
Why does my Ricoh Projector have an unusual color tone?
If the color tone or hue from your Ricoh Projector appears unusual, check if an appropriate color is selected in [WALL COLOR CORRECTION] and select the correct option. You can also adjust [TINT] in [PICTURE].
How to fix a Ricoh Projector image that isn't square to the screen?
If the image from your Ricoh Projector isn’t square to the screen, try repositioning the projector to improve its angle. You can also use the Keystone correction function to correct any trapezoid distortion.
What to do if my Ricoh PJ X6180N has a temperature problem?
If the temperature protector has been activated on your Ricoh Projector, and the room temperature is high, move the projector to a cooler place. If the problem persists, contact your dealer.
Why is the picture on my Ricoh PJ X6180N blurred?
If the picture on your Ricoh Projector is blurred, try adjusting the focus. Reposition the projector to improve its angle to the screen. Make sure the distance between the projector and screen is within the lens's adjustment range. Check if the lens has been shifted beyond its guaranteed range. If the projector has been exposed to cold and then warm conditions, condensation may have formed on the lens; let the projector stand until the condensation clears.
How to fix a Ricoh Projector remote control that is not working?
If your Ricoh Projector remote control isn’t working, try these steps: Install new batteries. Ensure there are no obstacles between the remote and the projector. Make sure you're within 22 feet (7 m) of the projector. If you want to perform computer mouse operations, connect the mouse receiver to the computer.
Why my Ricoh Projector does not turn on?
If your Ricoh Projector isn't turning on, first check that the power cord is properly plugged in and the Power button on the projector or remote is on. Ensure the lamp cover is correctly installed. Also, check if the projector has overheated due to insufficient ventilation or a warm room; if so, move it to a cooler location. If the lamp has exceeded its life, replace it and reset the lamp hours. The lamp may fail to light, wait a full minute and then turn on the power again. When using the projector at altitudes approximately 5500 feet/1600 meters or higher, be sure to set [FAN MODE] to [HIGH ALTITUDE].
General| Brightness | 6000 lumens |
|---|---|
| Resolution | XGA (1024 x 768) |
| Light Source | Lamp |
| Image Size | 30 - 300 inches |
| Speaker | 10W |
| Display Technology | DLP |
| Lamp Type | UHP |
| Native Resolution | XGA (1024 x 768) |
| Lamp Life | 4000 hours (Normal mode), 5000 hours (Eco mode) |
| Keystone Correction | Vertical ±30° |
| Input Terminals | HDMI, VGA, USB |
| Output Terminals | VGA |
| Control Terminals | RS-232C |
| Networking | LAN |
| Power Consumption | 350W (Normal mode), 280W (Eco mode) |
| Input Ports | HDMI, VGA, USB |
| Output Ports | VGA |
| Noise Level | 37 dB (Normal) |
General safety warnings and precautions for using the projector safely.
General advice on reading the manual and safety information before use.
Safety instructions to ensure projector longevity and prevent hazards.
Detailed safety measures to prevent fire and electrical shock hazards.
Instructions and warnings related to replacing the projector lamp.
Overview of the projector, its features, and capabilities.
Identifies and describes the physical parts of the projector.
Identifies and describes the buttons and functions of the remote control.
Instructions for connecting the projector to a computer and power source.
Procedure for powering on the projector and initial startup screen.
Methods for adjusting image size, position, focus, and tilt.
Steps to correct trapezoidal image distortion using the keystone function.
Procedure for safely powering down and putting the projector in standby mode.
Advanced adjustment for screen distortion using the Cornerstone feature.
Setting a keyword to prevent unauthorized operation of the projector.
Projecting PC screen images over a network without cables.
Remotely controlling a PC from the projector via a network connection.
Detailed explanation of input selection and signal type settings.
Settings for picture adjustment, including mode, color, and detail settings.
Configuration options for installation, basic settings, and projection modes.
Information on projector status, usage time, and system details.
Options for resetting projector settings to factory defaults.
Steps for replacing the projector lamp and associated filters.
Common problems and their solutions, including indicator messages.
To Next Page
