When the Printer Does Not Work as Expected > When the Printing Result Is Not as Expected > Using “Adjust Print Quality” > When the toner fixation is not adequate
Correction
Error Corrections
<Step 6>
"Manual Adjustment" tab: adjust fusibility raising the
temperature.
<Step 6>
"Manual adjustment" tab: Perform manual adjustment using the following
procedure when you specify [Black and White, Full Color, Full Color including
Special Color, Special Color], [Full Color including Special Color (High Quality
is applied)] or [Special Color] in "Select Color Mode".
1. Raise the heat roller temperature in "12: Machine: Image Quality 1232:
Fusing Temperature".
2. Lower the print speed in "12: Machine: Image Quality 1231: Print Speed".
Press [Print Test Chart] after you press [Apply Temporarily] to output a test
print. You can perform adjustments while confirming the fusibility. Perform Step
2 when you cannot resolve the problem even after you perform Step 1.
Introduction and Basic Operations
Basic Operation of the Machine > Turning On and Off the Power > Energy Saving Mode
Operator’s Guide
1. Getting Started > Turning On and Off the Power > Energy Saving Mode
Additional information
When the machine enters Low Power Mode (Standby for Printing Priority), the "No Signal” message appears on the control panel
even if there is no error in the cable connection.
Paper Settings
Adjustment Settings for Operators > 02: Machine: Image Quality > 0205: Density Difference Printing: Setting
Operator’s Guide
5. Adjustment Settings for Operators > 02: Machine: Image Quality > 0205: Density Difference Printing: Setting
Correction
Error Corrections
The sensitivity is updated when you execute [Density Difference
Printing: Across Feed] after specifying "0" in this setting.
The sensitivity is updated when you execute [Vertical Uneven Density
Correction] on the [Task] hub after specifying "0" in this setting.
Troubleshooting
When Paper or Another Item Is Jammed in the Printer > When Paper Is Jammed
Operator’s Guide
6. Troubleshooting > When Paper Is Jammed
Correction
Error Corrections
Multiple locations of paper jams may be indicated
simultaneously. If this occurs, check all the locations
that are displayed.
Multiple locations of paper jams may be indicated simultaneously. If this occurs,
check all the locations that are displayed. Detailed information about the paper
jam including the letter that indicates where the paper jam occurred appears
when you specify the part with a red mark indicating the location of the paper
jam on the figure at the upper part of the screen.
Specifications
Machine and Options Specifications > Special Notes When Using External Options > When Using the High Capacity Stacker > Removing paper
Operator’s Guide
1. Getting Started > Special Notes When Using External Options > When Using the High Capacity Stacker > Removing paper
Additional information
When you remove the printed paper, open the stacker front cover gently. Failure to do so may damage the part to which the cover is
mounted.
Specifications
Legal and Contact Information > Environmental Regulations > Energy Saving Functions > Specification
Operator’s Guide
8. Legal and Contact Information > Environmental Regulations > Energy Saving Functions > Specification
Correction
Error Corrections
Reduced electrical consumption in Sleep mode
*1
10W or less Reduced electrical consumption in Sleep mode
*1
35W or less
[Media] Hub
Additional information
If the descriptions of the following items are not available in the manual, see the balloon help that is displayed on the control panel.
"Edit media"
[Printer Adjustment] Hub
02: Machine: Image Quality > 0205 > Density Difference Printing: Setting
Correction
Error Corrections
After setting this value to zero, the setting will be applied when
you execute [Density Difference Printing: Across Feed].
After setting this value to zero, the setting will be applied when you
execute [Vertical Uneven Density Correction] on the [Task] hub.
Shared Maintenance Offering: Adjustment Item Menu Guide
Details of Menu Items in Adjustment Settings for Skilled Operators > [Machine: Image Quality] > 0205 [Density Difference Printing: Setting]
Correction
Error Corrections
If [Density Difference Printing: Across Feed] is executed after
setting the value to "0", the machine adjusts sensitivity and prints
50 sheets for adjustment.
If [Vertical Uneven Density Correction] on the [Task] hub is executed
after setting the value to "0", the machine adjusts sensitivity and prints
50 sheets for adjustment.
Shared Maintenance Offering: Regular Maintenance Guide
Read This First > Regular Maintenance Item List > Main Unit > Left Drawer
Correction
Error Corrections
163 #Left Drawer: Detection Unit 163 #Left Drawer: Detection Unit CIS Sensing Surface
Cleaning for General Users
Correction
Error Corrections
163 Left Drawer: Detection Unit 163 Left Drawer: Detection Unit CIS Sensing Surface
To Next Page
Loading...
