ROBB Smarrt - User Manual

To Next Page

Single Color Wall Mounted ZigBee Remote Controller

70100005

55.57 mm

71.20 mm

11 mm

Function introduction

Important: Read All Instructions Prior to Installation

Front side

Back side

Battery: CR2450

Before the first use, please remove the protective film

55.57 mm

71.20 mm

The remote control can be fixed on

the wall with 3M glue or screw.

71.2x71.2x13.6mm

Press and hold down both keys together to search and

pair to ZigBee network or factory reset the controller.

Group 1

Click to turn on. Press and

hold down to increase

light intensity.

Note: This remote

supports 4 groups for

binding max. 30 lighting

devices.

Transmission Range

(free field)

30m

Operating temperature

0-40°C

Relative humidity

8% to 80%

Dimming Range

0.1%-100%

Power Supply

3VDC (CR2450)

Operation Frequency

2.4GHz

Dimensions

Protection Type

IP20

Click to turn off. Press and

hold down to decrease

light intensity.

Group 1

Group 3 Group 3

Group 2 Group 2

Group 4 Group 4

Product Data

• 2.4 GHz global operation

• Enables to pair ZigBee lighting devices via touchlink

commissioning without coordinator

• Battery powered remote with low power consumption

• Enables to control both single color lighting devices

• Compatible with universal single color ZigBee lighting

devices

• Supports find and bind mode to pair with ZigBee lighting

devices

• Supports 4 groups for binding max. 30 lighting devices

• ZigBee dim remote based on ZigBee 3.0

• Transmission range up to 30m

• Compatible with universal ZigBee Gateway products

• Identify • Group • On/off • Level control • Ota

ZigBee Clusters Supported by This Remote Are As Follows:

Input clusters:

• Basic • Power Configuration • Identify • Diagnostics

Output clusters:

Network pairing mode: click both buttons 3 times to

set the remote into network pairing mode (the remote

should not belong to any gateway network).

Factory reset: click both buttons 3 times to

reset the remote (the remote should already

be paired to a gateway).

Quick Start (Simplified operation compared to standard operations in the part “Operation”)

Touchlink + Add Group 1: Press and hold

down both keys for 3 seconds to start

touchlink and link light device to group 1.

Touchlink + Add Group 2: Press and hold

down both keys for 3 seconds to start

touchlink and link light device to group 2.

Touchlink + Add Group 3: Press and hold

down both keys for 3 seconds to start

touchlink and link light device to group 3.

Touchlink + Add Group 4: Press and hold

down both keys for 3 seconds to start

touchlink and link light device to group 4.

• This device contains a button lithium battery that shall be stored and disposed properly.

• Do not ingest battery, Chemical Burn Hazard

• DO NOT expose the device to moisture.

• This product contains a coin / button cell battery. If the coin / button cell battery is swallowed,

it can cause severe internal burns in just 2 hours and can lead to death

• Keep new and used batteries away from children.

from children.

• If you think batteries might have been swallowed or placed inside any part of the body, seek

immediate medical attention

• If the battery compartment does not close securely, stop using the product and keep it away

Safety & Warnings

Need help?

Do you have a question about the ROBB Smarrt and is the answer not in the manual?

This document describes the Single Color Wall Mounted ZigBee Remote Controller, a device designed for controlling ZigBee lighting systems.

Function Description

The Single Color Wall Mounted ZigBee Remote Controller is a wireless device that communicates with a variety of ZigBee compatible systems. It transmits wireless radio signals to remotely control compatible systems. This controller supports binding up to 30 lighting devices and enables control of single color ZigBee lighting devices.

The device features four control groups, each with a push button interface. Users can press and hold down both keys together to search and pair to a ZigBee network or factory reset the controller. Each group has an LED indicator to show its status.

TouchLink Pairing: The controller supports TouchLink pairing to directly link with ZigBee lighting devices without needing a coordinator.

TouchLink Add Group 1: Press and hold down both keys for 3 seconds to start TouchLink and link a light device to group 1.
TouchLink Add Group 2: Press and hold down both keys for 3 seconds to start TouchLink and link a light device to group 2.
TouchLink Add Group 3: Press and hold down both keys for 3 seconds to start TouchLink and link a light device to group 3.
TouchLink Add Group 4: Press and hold down both keys for 3 seconds to start TouchLink and link a light device to group 4.

Network Pairing: The controller can also be paired to a ZigBee network via a coordinator. To enter network pairing mode, press both buttons 3 times to search for a network.

Factory Reset: To perform a factory reset, press both buttons 3 times. This will remove all binding information and reset the device to its default settings.

Battery Power Monitor Function: The remote will report battery power value to the coordinator under the following situations:

When powered on.
When pressing both buttons and buttons of group 2 simultaneously.
When operating the switch to send data packets (over 4 hours since last operation).
When added to the network by a coordinator.

Important Technical Specifications

Product Data:
- Operation Frequency: 2.4GHz
- Transmission Range (free field): 30m
- Power Supply: 3VDC (CR2450)
- Operating Temperature: 0-40°C
- Relative Humidity: 80% to 80%
- Dimming Range: 0.1%-100%
- Dimensions: 71.2x71.2x13.6mm
- Protection Type: IP20
ZigBee Clusters Supported by This Remote Are As Follows:
- Input clusters: Basic, Power Configuration, Identify, Diagnostics
- Output clusters: Identify, Group, On/Off, Level Control, Ota
Safety & Warnings:
- This device contains a button lithium battery that shall be stored and disposed properly.
- DO NOT expose the device to moisture.
- Do not ingest battery, Chemical Burn Hazard.
- This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
- Risk of explosion if the battery is replaced by an incorrect type.
- Replacement of a battery with an incorrect type that can defeat a safeguard (for example, in the case of some lithium battery types).
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

Usage Features

General Operation:

Group 1: Click to turn on. Press and hold down to increase light intensity.
Group 2: Click to turn on. Press and hold down to increase light intensity.
Group 3: Click to turn on. Press and hold down to increase light intensity.
Group 4: Click to turn on. Press and hold down to increase light intensity.
Note: This remote supports 4 groups for binding max. 30 lighting devices.

ZigBee Network Pairing Through Coordinator or Hub (Added to a ZigBee Network):

Remove the remote from previous ZigBee network if it has already been added to it, otherwise pairing will fail. Please refer to the part "Factory Reset Manually".
From your ZigBee controller or hub interface, choose to delete or reset the remote as instructed, indicator flashes 3 times quickly to indicate successful removing.
Press and hold down both buttons until LED indicator turns on.
Immediately short press to search nearby network, indicator flashes every 1 second, 20 seconds timeout if there is no network. Indicator will then blink 10 times quickly for successful pairing.
- Note 1: After pairing successfully, the remote information will appear on the controller or hub interface.
- Note 2: No remote information will appear on the hub interface if pairing to Philips Hue Bridge.

TouchLink to a ZigBee Lighting Device:

Set the ZigBee lighting device to start TouchLink commissioning, please refer to its manual to learn how.
Bring the remote within 10cm of the lighting device.
Short press ON button 1 of group 1/2/3/4 to choose a group that you would like to pair to the device.
Immediately short press 5 times to start TouchLink commissioning of the remote. LED indicator flashes fast for 3s, then flash 8 times slowly to indicate successful pairing. The device will blink twice.
Press and hold down both buttons until LED indicator turns on.
- Note 1: Directly TouchLink (both not added to a ZigBee network): please first factory reset both the remote and device, each remote can link with max. 30 devices, please make sure the first linked device is always powered on when touchlink the remote with 2nd device and more devices.
- Note 2: TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
- Note 3: To control by both remote and hub, add both remote and device to network first then TouchLink, after TouchLink, the device can be controlled by the linked remotes and ZigBee hub together.

Factory Reset Manually:

Immediately short press 5 times continuously, indicator flashes 3 times quickly to indicate successful reset.
Press and hold down both buttons until LED indicator turns on.
- Note: All configuration parameters will be reset after the remote is reset or removed from the network.

TouchLink a Paired ZigBee Lighting Device:

Set the TouchLink paired ZigBee device to start TouchLink commissioning, please refer to its manual to learn how.
Bring the remote within 10cm of the lighting device.
Short press ON button 1 of group 1/2/3/4 to choose a group that the device was TouchLink paired to.
Immediately short press 5 times twice to start TouchLink removing of the remote. LED indicator flashes fast for 3s, then flash 8 times slowly to indicate successful removing.
Press and hold down both buttons until LED indicator turns on.

Factory Reset a Lighting Device (Touch Reset):

Set the ZigBee device to start TouchLink commissioning, refer to its manual.
Bring the remote within 10cm of the lighting device.
Immediately short press 5 times to start Touch Reset of the remote. LED indicator flashes fast for 3s, then flash 3 times slowly to indicate successful reset.
Press and hold down both buttons until LED indicator turns on.
- Note: The device shall be added to a network, the remote added to the same one or not added to any network.

Clear All Find and Bind Mode Paired Lighting Devices:

Short press ON button 1 of group 1/2/3/4 to choose the group that you would like to unbind all devices.
Short press 5 times continuously to clear all bound lighting devices. LED indicator flashes 8 times for successful unbinding.
Press and hold down both buttons until LED indicator turns on.

Setup a Network & Add Devices to the Network (No Coordinator or Hub Required):

Factory reset the remote and the lighting device, refer to their manuals.
Setup the TouchLink the remote and device to setup a network, refer to their manuals.
Press and hold down both buttons until LED indicator turns on.
Short press to enable the network to discover and add devices. LED indicator will flash twice. 180 seconds timeout, repeat the operation.
Set another remote into network pairing mode and pair it to the network, refer to its manual.
Add more remotes to the network as you would like.
Factory reset the lighting devices that you would then add them to the network, refer to their manuals.
TouchLink to pair the added remotes and lighting devices, refer to their manuals. Each remote can link with max. 30 lighting devices. Each lighting device can be linked by max. 30 remotes.

OTA: The remote supports firmware updating through OTA, and will acquire new firmware from ZigBee controller or hub every 10 minutes automatically.

How to Check Whether The Remote Belongs to a Network or not: Short press any button, indicator blinking means the remote has already been added to a network, no blinking of indicator means the remote does not belong to any network.

Maintenance Features

Installation:

Remove battery insulator:
- Use tool to open the silicone gel battery cover.
- Pull out the battery insulator.
- Install the silicone battery cover back.
Install the controller to wall (2 methods):
- Method 1: Stick 3M glue on the back of the bracket, then stick the bracket to the wall.
- Method 2: Screw the bracket to the wall.
- After the bracket is fixed, clip the frame and control part to the bracket in sequence.
- The remote control can be fixed on the wall with 3M glue or screw.

Mounting: The key part of this controller is an universal one, especially rotary standard switch element that can be integrated in numerous frames by different manufactures as below list:

BERKER: S1, B1, B3, B7 glass
GIRA: Standard55, E2, Event, Esprit
JUNG: A500, Aplus
MERTEN: M-smart, M-Arc, M-Plan

Battery: CR2450. Before the first use, please remove the protective film.

ROBB Smarrt Specifications

General

Brand	ROBB
Model	Smarrt
Category	Remote Control
Language	English