Roger Technology B70/1DCHP - Page 73

EN
73
 
'SRƼKYVMRKVEHMSGLERRIP46N.B.: With ROGER TECHNOLOGY plug-in radio receiver board.
 
'SRƼKYVMRKVEHMSGLERRIP46N.B.: With ROGER TECHNOLOGY plug-in radio receiver board.

STEP MODE.

PARTIAL OPENING

OPENING

CLOSING.

STOP.

Courtesy light. The output COR is managed from the remote control. The light remains lit as long as the remote control
is active. The parameter  is ignored.

Courtesy light in step mode (PP). The output COR is managed from the remote control.
The remote control turns the courtesy light on and off. The parameter  is ignored.

78)413()[MXLGSRƼVQEXMSRJSVWEJIX]
(1)

4%68-%034)2-2+[MXLGSRƼVQEXMSRJSVWEJIX]
(1)

34)2-2+[MXLGSRƼVQEXMSRJSVWEJIX]
(1)

'03796)[MXLGSRƼVQEXMSRJSVWEJIX]
(1)
(1)
8STVIZIRXKEXIQERSIYZVIWGEYWIHF]EGGMHIRXEPP]TVIWWMRKEVIQSXIGSRXVSPFYXXSRGSRƼVQEXMSRMWVIUYMVIHXSIREFPIXLIGSQ-
mand. Example: parameters   and   set:
• 4VIWWMRKXLI',%FYXXSRSRXLI VIQSXIGSRXVSPWIPIGXWXLIWXIT QSHIJYRGXMSR [LMGLQYWX FIGSRƼVQIH[MXLMRWIGSRHWF]
pressing CHB on the remote control. Press CHB to activate partial opening.
 
'SRƼKYVMRKƽEWLMRKPMKLXJVIUYIRG]

8LIJVIUYIRG]MWWIXIPIGXVSRMGEPP]JVSQXLIƽEWLMRKPMKLXYRMX

7PS[ƽEWL

0MKLXƽEWLIWWPS[P][LIRKEXISTIRWVETMHP][LIRKEXIGPSWIW
 
Selecting courtesy light mode

Disabled.

4907)8LIGSYVXIW]PMKLXMPPYQMREXIWFVMIƽ]EXXLIWXEVXSJIEGLQERSIYZVI

ACTIVE. The light remains lit for the entire duration of the manoeuvre.

From 3 to 90 s. The light remains lit for the time period set after the manoeuvre is completed.

From 2 to 9 minutes. The light remains lit for the time period set after the manoeuvre is completed.
 
'PSGOGSRXEGXGSRƼKYVEXMSR
When the clock function is active, the gate opens and remains open.
At the end of the programmed time set with the external device (clock), the gate closes.

When the clock function is active, the gate opens and remains open. Any command signal received is ignored.

When the clock function is active, the gate opens and remains open. Any command signal received is accepted. When
the gate returns to the completely open position, the clock function is reactivated.
  
Enable safeguarded gate closure/opening
Enabling this parameter ensures that the gate is not left open due to an incorrect and/or accidental command.
This function is NOT enabled if:
• the gate receives a STOP command;
• the sensitive edge intervenes, detecting an obstacle in the same direction in which the function is enabled. If instead
the sensitive edge detects an obstacle during the movement opposite to the one guaranteed, the function remains
active.
• the number of closure attempts set by parameter $ has been reached;
• the acquired position is lost (perform position recovery, see chapter 20).

Disabled. The parameter  is not displayed.

Enabled.
After a period of time set with parameter XLIGSRXVSPYRMXWMKREPWEWIGSRH[EVRMRK[MXLXLIƽEWLMRKPMKLXVIKEVH-
less of the parameter $, and then closes the gate.

Enabled.
If the gate is closed as a result of a step mode command, after a period of time set with parameter , the control unit
WMKREPWEWIGSRH[EVRMRK[MXLXLIƽEWLMRKPMKLXVIKEVHPIWWSJXLITEVEQIXIV$), and then the gate closes.
If the gate is stopped by the obstacle detection system during a closure manoeuvre, the gate closes after a period of
time set with parameter .
If the gate is stopped by the obstacle detection system during an opening manoeuvre, the gate closes after a period of
time set with parameter .