Roger Technology B70/1DCHP - Page 39

EN
73
 
(TSܪLZWNSLWFINTHMFSSJQ57N.B.: With ROGER TECHNOLOGY plug-in radio receiver board.
 
(TSܪLZWNSLWFINTHMFSSJQ57N.B.: With ROGER TECHNOLOGY plug-in radio receiver board.

STEP MODE.

PARTIAL OPENING

OPENING

CLOSING.

STOP.

Courtesy light. The output COR is managed from the remote control. The light remains lit as long as the remote
control is active. The parameter  is ignored.

Courtesy light in step mode (PP). The output COR is managed from the remote control.
The remote control turns the courtesy light on and off. The parameter  is ignored.

89*524)*\NYMHTSܪWRFYNTSKTWXFKJY^
(1)

5&79.&145*3.3,\NYMHTSܪWRFYNTSKTWXFKJY^
(1)

45*3.3,\NYMHTSܪWRFYNTSKTWXFKJY^
(1)

(148:7*\NYMHTSܪWRFYNTSKTWXFKJY^
(1)
(1)
9TUWJ[JSYLFYJRFSTJZ[WJXHFZXJIG^FHHNIJSYFQQ^UWJXXNSLFWJRTYJHTSYWTQGZYYTSHTSܪWRFYNTSNXWJVZNWJIYTJSFGQJYMJHTR-
mand. Example: parameters   and   set:
• 5WJXXNSLYMJ(-&GZYYTSTSYMJWJRTYJHTSYWTQXJQJHYXYMJ XYJURTIJKZSHYNTS\MNHMRZXYGJHTSܪWRJI \NYMNSXJHTSIXG^
pressing CHB on the remote control. Press CHB to activate partial opening.
 
(TSܪLZWNSLܫFXMNSLQNLMYKWJVZJSH^

9MJKWJVZJSH^NXXJYJQJHYWTSNHFQQ^KWTRYMJܫFXMNSLQNLMYZSNY

8QT\ܫFXM

1NLMYܫFXMJXXQT\Q^\MJSLFYJTUJSXWFUNIQ^\MJSLFYJHQTXJX
 
Selecting courtesy light mode

Disabled.

5:18*9MJHTZWYJX^QNLMYNQQZRNSFYJXGWNJܫ^FYYMJXYFWYTKJFHMRFSTJZ[WJ

ACTIVE. The light remains lit for the entire duration of the manoeuvre.

From 3 to 90 s. The light remains lit for the time period set after the manoeuvre is completed.

From 2 to 9 minutes. The light remains lit for the time period set after the manoeuvre is completed.
 
(QTHPHTSYFHYHTSܪLZWFYNTS
When the clock function is active, the gate opens and remains open.
At the end of the programmed time set with the external device (clock), the gate closes.

When the clock function is active, the gate opens and remains open. Any command signal received is ignored.

When the clock function is active, the gate opens and remains open. Any command signal received is accepted. When
the gate returns to the completely open position, the clock function is reactivated.
  
Enable safeguarded gate closure/opening
Enabling this parameter ensures that the gate is not left open due to an incorrect and/or accidental command.
This function is NOT enabled if:
• the gate receives a STOP command;
• the sensitive edge intervenes, detecting an obstacle in the same direction in which the function is enabled. If instead the
sensitive edge detects an obstacle during the movement opposite to the one guaranteed, the function remains active.
• the number of closure attempts set by parameter $ has been reached;
• the acquired position is lost (perform position recovery, see chapter 20).

Disabled. The parameter  is not displayed.

Enabled.
After a period of time set with parameter YMJHTSYWTQZSNYXNLSFQXFXJHTSI\FWSNSL\NYMYMJܫFXMNSLQNLMYWJLFWI-
less of the parameter $, and then closes the gate.

Enabled.
If the gate is closed as a result of a step mode command, after a period of time set with parameter , the control unit
XNLSFQXFXJHTSI\FWSNSL\NYMYMJܫFXMNSLQNLMYWJLFWIQJXXTKYMJUFWFRJYJW$), and then the gate closes.
If the gate is stopped by the obstacle detection system during a closure manoeuvre, the gate closes after a period of
time set with parameter .
If the gate is stopped by the obstacle detection system during an opening manoeuvre, the gate closes after a period of
time set with parameter .