R&S
®
CMW 500 GPRF Applications
GPRF Command Reference
Operating Manual 1202.3986.32 – 03 184
Trigger Settings Page
CONFigure:GPRF:MEAS<i>:POWer:TRIGger:SOURce...........................................................................189
CONFigure:GPRF:MEAS<i>:POWer:TRIGger:SLOPe .............................................................................189
CONFigure:GPRF:MEAS<i>:POWer:TRIGger:THReshold .......................................................................189
CONFigure:GPRF:MEAS<i>:POWer:TRIGger:OFFSet ............................................................................189
CONFigure:GPRF:MEAS<i>:POWer:TRIGger:TOUT ...............................................................................190
CONFigure:GPRF:MEAS<i>:POWer:TRIGger:MODE ..............................................................................190
List Configuration Page
CONFigure:GPRF:MEAS<i>:POWer:LIST................................................................................................190
CONFigure:GPRF:MEAS<i>:POWer:LIST:COUNt?..................................................................................190
CONFigure:GPRF:MEAS<i>:POWer:LIST:STARt ....................................................................................191
CONFigure:GPRF:MEAS<i>:POWer:LIST:STOP .....................................................................................191
CONFigure:GPRF:MEAS<i>:POWer:LIST:FREQuency............................................................................191
CONFigure:GPRF:MEAS<i>:POWer:LIST:ENPower................................................................................191
Measurement Results Page
FETCh:GPRF:MEAS<i>:POWer[:RMS]:CURRent? .................................................................................192
FETCh:GPRF:MEAS<i>:POWer:MINimum:CURRent?.............................................................................192
FETCh:GPRF:MEAS<i>:POWer:MAXimum:CURRent?............................................................................192
FETCh:GPRF:MEAS<i>:POWer[:RMS]:AVERage?..................................................................................192
FETCh:GPRF:MEAS<i>:POWer:PEAK:MINimum?...................................................................................192
FETCh:GPRF:MEAS<i>:POWer:PEAK:MAXimum? .................................................................................192
READ:GPRF:MEAS<i>:POWer[:RMS]:CURRent? ...................................................................................192
READ:GPRF:MEAS<i>:POWer:MINimum:CURRent? ..............................................................................192
READ:GPRF:MEAS<i>:POWer:MAXimum:CURRent?.............................................................................192
READ:GPRF:MEAS<i>:POWer[:RMS]:AVERage? ...................................................................................192
READ:GPRF:MEAS<i>:POWer:PEAK:MINimum?....................................................................................192
READ:GPRF:MEAS<i>:POWer:PEAK:MAXimum?...................................................................................192
FETCh:GPRF:MEAS<i>:POWer:SDEViation? .........................................................................................192
READ:GPRF:MEAS<i>:POWer:SDEViation? ..........................................................................................192
7.4.3.2 Measurement Control and States
The following commands control the measurement and return the current
measurement state.
INITiate:GPRF:MEAS<i>:POWer
ABORt:GPRF:MEAS<i>:POWer
STOP:GPRF:MEAS<i>:POWer
Starts, stops, or aborts the measurement; see Measurement Control:
INITiate... starts or restarts the measurement; the R&S CMW 500 enters the
To Next Page
Loading...
