Rohde & Schwarz ESW Series - Page 630

Remote Commands in the Receiver Application
R&S
®
ESW
630User Manual 1177.6298.02 ─ 08
[SENSe:]CORRection:SWITch:DEFault[:COMMand]..........................................................631
[SENSe:]CORRection:SWITch:DEFault:EXECute..............................................................632
[SENSe:]CORRection:SWITch:DELete.............................................................................632
[SENSe:]CORRection:SWITch:INPut................................................................................632
[SENSe:]CORRection:SWITch:LOAD...............................................................................633
[SENSe:]CORRection:SWITch:NAME.............................................................................. 633
[SENSe:]CORRection:SWITch:OPC.................................................................................633
[SENSe:]CORRection:SWITch:RANGe<range>[:COMMand].............................................. 633
[SENSe:]CORRection:SWITch:RANGe<range>:EXECute.................................................. 634
[SENSe:]CORRection:SWITch:SCPI................................................................................ 634
[SENSe:]CORRection:SWITch:SELect............................................................................. 634
[SENSe:]CORRection:SWITch:STORe.............................................................................635
[SENSe:]CORRection:SWITch:WAIT................................................................................635
[SENSe:]CORRection:TRANsducer:INPut<rf>:ACTive?..................................................... 635
[SENSe:]CORRection:TRANsducer:ACTive?.................................................................... 635
[SENSe:]CORRection:TRANsducer:ADJust:RLEVel[:STATe].............................................. 635
[SENSe:]CORRection:TRANsducer:CATalog?...................................................................636
[SENSe:]CORRection:TRANsducer:COMMent..................................................................636
[SENSe:]CORRection:TRANsducer:DATA........................................................................ 636
[SENSe:]CORRection:TRANsducer:DELete......................................................................637
[SENSe:]CORRection:TRANsducer:SCALing....................................................................637
[SENSe:]CORRection:TRANsducer:SELect......................................................................637
[SENSe:]CORRection:TRANsducer:INPut<rf>[:STATe].......................................................637
[SENSe:]CORRection:TRANsducer[:STATe]..................................................................... 637
[SENSe:]CORRection:TRANsducer:UNIT.........................................................................638
[SENSe:]CORRection:TSET:BREak.................................................................................638
[SENSe:]CORRection:TSET:CATalog?............................................................................. 638
[SENSe:]CORRection:TSET:COMMent............................................................................ 639
[SENSe:]CORRection:TSET:DELete................................................................................ 639
[SENSe:]CORRection:TSET:RANGe<range>....................................................................639
[SENSe:]CORRection:TSET:SELect.................................................................................640
[SENSe:]CORRection:TSET:UNIT................................................................................... 640
[SENSe:]CORRection:TSET:INPut<rf>[:STATe]................................................................. 640
[SENSe:]CORRection:TSET[:STATe]................................................................................640
MMEMory:LOAD<n>:TFACtor <FileName>
Loads the transducer factor from the selected file in .CSV format.
Suffix:
<n>
.
irrelevant
Parameters:
<FileName> String containing the path and name of the CSV import file.
Example:
MMEM:LOAD:TFAC 'C:\TEST.CSV'
MMEMory:STORe<n>:TFACtor <FileName>, <TransdName>
This command exports transducer factor data to an ASCII (CSV) file.
General Instrument Setup