Rohde & Schwarz RTE - Page 1144

Remote control commands
R&S
®
RTE
1144User Manual 1326.1032.02 ─ 20
Some of the commands in the following chapter are asynchronous. An overlapping or
asynchronous command does not automatically finish executing before the next com-
mand starts executing. If overlapping commands must be executed in a defined order,
e.g. to avoid wrong measurement results, they must be serviced sequentially.
To prevent an overlapping execution of commands, one of the commands *OPC,
*OPC? or *WAI can be used after the command or a command set.
For more information, see:
●
www.rohde-schwarz.com/rc-via-scpi, chapter "Command Sequence and Synchro-
nization"
●
Chapter 18.3, "Programming examples", on page 1054
ZVC:BANDwidth...........................................................................................................1144
ZVC:TYPE...................................................................................................................1145
ZVC:Z<m>:I<n>:BANDwidth?........................................................................................1145
ZVC:Z<m>:I<n>:IMPedance..........................................................................................1145
ZVC:Z<m>:I<n>:OFFSet...............................................................................................1146
ZVC:RESCoupled........................................................................................................ 1146
ZVC:Z<m>:I<n>:OVERload:RSTO................................................................................. 1146
ZVC:Z<m>:I<n>:OVERload:VALue?...............................................................................1147
ZVC:Z<m>:I<n>:POSition..............................................................................................1147
ZVC:Z<m>:I<n>:SCALe................................................................................................ 1148
ZVC:Z<m>:I<n>:SHUNt:EVALue....................................................................................1148
ZVC:Z<m>:I<n>:SHUNt:MODE......................................................................................1148
ZVC:Z<m>:I<n>:SHUNt:MAXCurrent..............................................................................1148
ZVC:Z<m>:I<n>:SHUNt:MXCValue?.............................................................................. 1149
ZVC:Z<m>:I<n>:SHUNt:MAXVoltage..............................................................................1149
ZVC:Z<m>:I<n>:SKEW.................................................................................................1150
ZVC:Z<m>:I<n>[:STATe]............................................................................................... 1150
ZVC:Z<m>:V<n>:BANDwidth?.......................................................................................1150
ZVC:Z<m>:V<n>:IMPedance.........................................................................................1151
ZVC:Z<m>:V<n>:OFFSet..............................................................................................1151
ZVC:Z<m>:V<n>:OVERload:RSTO................................................................................1151
ZVC:Z<m>:V<n>:OVERload:VALue?..............................................................................1152
ZVC:Z<m>:V<n>:POSition............................................................................................ 1152
ZVC:Z<m>:V<n>:SCALe...............................................................................................1152
ZVC:Z<m>:V<n>:SKEW................................................................................................1153
ZVC:Z<m>:V<n>[:STATe].............................................................................................. 1153
ZVC:Z<m>:ID:NAME?.................................................................................................. 1153
ZVC:Z<m>:ID:PARTnumber?.........................................................................................1153
ZVC:Z<m>:ID:SRNumber?............................................................................................1154
ZVC:Z<m>:ID:SWVersion?............................................................................................1154
ZVC:Z<m>:I<n>:ZERComp:DETect................................................................................1154
ZVC:Z<m>:I<n>:ZERComp:USE....................................................................................1154
ZVC:Z<m>:I<n>:ZERComp:STATe?............................................................................... 1155
ZVC:BANDwidth <Bandwidth>
Sets the bandwidth limit of the probe. The bandwidth specifies the maximum frequency
at which a purely sinusoidal signal is still transferred at 89 % (0.1 dB) of its amplitude.
Acquisition and setup