Rohde & Schwarz RTP Series - Page 1947

Remote control commands
R&S
®
RTP
1947User Manual 1337.9952.02 ─ 12
22.17.16.2 Trigger
The trigger suffix <m> is always 1 and can be omitted. It selects the trigger event: Only
the A-trigger is available for triggering on serial buses.
To trigger on a serial bus, make sure that:
●
TRIGger<m>:SOURce[:SELect] is set to SBUS.
●
The sources of the serial bus are channel signals: use BUS<m>:...:SOURce
commands.
●
Decoding is enabled: BUS<m>[:STATe] is set to ON.
TRIGger<m>:CMSB:TYPE............................................................................................1947
TRIGger<m>:CMSB:PATTern........................................................................................1948
TRIGger<m>:CMSB:ICONdition.................................................................................... 1948
TRIGger<m>:CMSB:IMIN............................................................................................. 1948
TRIGger<m>:CMSB:IMAX............................................................................................ 1949
TRIGger<m>:CMSB:NRZ:WRDLength...........................................................................1949
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:ENABle....................................................... 1949
TRIGger<m>:CMSB:ADVanced:FRENable..................................................................... 1949
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:ENABle...........................................1949
TRIGger<m>:CMSB:ADVanced:FIENable.......................................................................1949
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:BIT.................................................1950
TRIGger<m>:CMSB:ADVanced:BIT...............................................................................1950
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:DMAX.............................................1950
TRIGger<m>:CMSB:ADVanced:DMAX...........................................................................1950
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:DMIN..............................................1951
TRIGger<m>:CMSB:ADVanced:DMIN............................................................................1951
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:DOPerator...................................... 1951
TRIGger<m>:CMSB:ADVanced:DOPerator.....................................................................1951
TRIGger<m>:CMSB:ADVanced:ERRor<n>:ENABle........................................................ 1951
TRIGger<m>:CMSB:ADVanced:ERENable.....................................................................1951
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:IMAX.............................................. 1952
TRIGger<m>:CMSB:ADVanced:IMAX............................................................................ 1952
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:IMIN............................................... 1952
TRIGger<m>:CMSB:ADVanced:IMIN............................................................................. 1952
TRIGger<m>:CMSB:ADVanced:FRAMe<n>:FLD<o>:IOPerator........................................1952
TRIGger<m>:CMSB:ADVanced:IOPerator......................................................................1952
TRIGger<m>:CMSB:TYPE <Type>
Selects the trigger type for custom serial bus analysis.
Suffix:
<m>
.
1..3
Parameters:
<Type> STARt | PATTern | ADVanced
STARt
Triggers on the frame start, which is the end of the gap time as
specified in BUS<m>:CMSB:GAPTime:VALue on page 1941
Protocols