Remote control commands
R&S
®
RTP
1352User Manual 1337.9952.02 ─ 12
Parameters:
<Source2> C1W1 | C1W2 | C1W3 | C2W1 | C2W2 | C2W3 | C3W1 | C3W2 |
C3W3 | C4W1 | C4W2 | C4W3 | M1 | M2 | M3 | M4 | M5 | M6 |
M7 | M8 | R1 | R2 | R3 | R4 | XY1 | XY2 | XY3 | XY4 | D0 | D1 |
D2 | D3 | D4 | D5 | D6 | D7 | D8 | D9 | D10 | D11 | D12 | D13 |
D14 | D15 | MSOB1 | MSOB2 | MSOB3 | MSOB4 | TRK1 |
TRK2 | TRK3 | TRK4 | TRK5 | TRK6 | TRK7 | TRK8 | SG1 |
SG2 | SG3 | SG4 | SG5 | SG6 | SG7 | SG8 | SG1TL1 | SG1TL2 |
SG2TL1 | SG2TL2 | SG3TL1 | SG3TL2 | SG4TL1 | SG4TL2 |
SG5TL1 | SG5TL2 | SG6TL1 | SG6TL2 | SG7TL1 | SG7TL2 |
SG8TL1 | SG8TL2 | Z1V1 | Z1V2 | Z1V3 | Z1V4 | Z1I1 | Z1I2 |
Z1I3 | Z1I4 | Z2V1 | Z2V2 | Z2V3 | Z2V4 | Z2I1 | Z2I2 | Z2I3 |
Z2I4 | DIFF1 | DIFF2 | COMMON1 | COMMON2 | EYE1 | EYE2 |
EYE3 | EYE4 | TDRZ | TDRH | TDRR | BATHtub1 | BMEas1 |
SRESponse1 | SRTRack1 | SDTRack1 | TJTRack1 |
DJTRack1 | DDJTrack1 | PJTRack1 | RJOTRack1 |
TJSPectrum1 | DDJSpectrum1 | PJOSPectrum1 |
RJSPectrum1 | BATHtub2 | BMEas2 | SRESponse2 |
SRTRack2 | SDTRack2 | TJTRack2 | DJTRack2 | DDJTrack2 |
PJTRack2 | RJTORack2 | TJSPectrum2 | DDJSpectrum2 |
PJSPectrum2 | RJOSPectrum2 | SEYE1 | SEYE2 | SDHist1 |
TJHist1 | DJHist1 | DDJHist1 | PJHist1 | RJOHist1 | SRHist2 |
SDHist2 | TJHist2 | DJHist2 | DDJHist2 | PJHist2 | RJOHist2 |
NBAThtub1 | NBMeas1 | TNHist1 | DNHist1 | DDNHist1 |
PNHist1 | RNOHist1 | TNTRack1 | DNTRack1 | DDNTrack1 |
PNTRack1 | RNOTRack1 | TNSPectrum1 | DDNSpectrum1 |
PNSPectrum1 | RNSPectrum1 | NBAThtub2 | NBMeas2 |
TNHist2 | DNHist2 | DDNHist2 | PNHist2 | RNHist2 | TNTRack2 |
DNTRack2 | DDNTrack2 | PNTRack2 | RNOTRack2 |
TNSPectrum2 | DDNSpectrum2 | PNSPectrum2 |
RNOSPectrum2
Second source of the cursor measurement, see Chapter 22.4.2,
"Waveform parameter", on page 1145
*RST:
C2W1
Usage: Asynchronous command
Firmware/software: FW 3.60
CURSor<m>:USSource <UseSource2>
Enables the second cursor source. To select the second source, use CURSor<m>:
SSOurce on page 1351.
If enabled, the second corsor lines Cx.2 measure on the second source. Using a sec-
ond source, you can measure differences between two channels with cursors.
Suffix:
<m>
.
1..4
Selects the cursor set.
Cursor measurements
To Next Page
Loading...
