Rohde & Schwarz SMIQ02B - Page 44

SMIQ Contents
1125.5610.12 23 E-9
Fig. 2-197 Menu DIGITAL STD - GSM/EDGE - SELECT SLOT – ALL_DATA, SMIQ
equipped with Modulation Coder SMIQB20 and Data Generator SMIQB11 .......... 2.304
Fig. 2-198 Menu DIGITAL STD - GSM/EDGE - SELECT SLOT – EDGE, SMIQ equipped
with Modulation Coder SMIQB20 and Data Generator SMIQB11 .......................... 2.305
Fig. 2-199 Menu DIGITAL STD - DECT, SMIQ equipped with Modulation Coder SMIQB20
and Data Generator SMIQB11 ............................................................................... 2.311
Fig. 2-200 Menu DIGITAL STD - DECT - MODULATION... .................................................... 2.311
Fig. 2-201 Menu DIGITAL STD - DECT_TRIGGER..., SMIQ equipped with Modulation
Coder SMIQB20 and Data Generator SMIQB11.................................................... 2.313
Fig. 2-202 Menu DIGITAL STD - DECT - CLOCK..., SMIQ equipped with Modulation Coder
SMIQB20 and Data Generator SMIQB11............................................................... 2.315
Fig. 2-203 Menu DIGITAL STD - DECT - POWER RAMP CONTROL... , SMIQ equipped
with Modulation Coder SMIQB20 and Data Generator SMIQB11 .......................... 2.316
Fig. 2-204 Menu DIGITAL STD - DECT - SAVE/RCL FRAME, SMIQ equipped with
Modulation Coder SMIQB20 and Data Generator SMIQB11 ................................. 2.317
Fig. 2-205 Menu DIGITAL STD - DECT - SELECT SLOT, SMIQ equipped with Modulation
Coder SMIQB20 and Data Generator SMIQB11.................................................... 2.319
Fig. 2-206 Signal flow of ARB generator.................................................................................. 2.323
Fig. 2-207 Block diagram SMIQB60 ........................................................................................ 2.324
Fig. 2-208 Signal flow SMIQB60.............................................................................................. 2.325
Fig. 2-209 Trigger signals SMIQB60........................................................................................ 2.326
Fig. 2-210 ARB MOD menu..................................................................................................... 2.327
Fig. 2-211 ARB MOD - TRIGGER... menu .............................................................................. 2.329
Fig. 2-212 ARB MOD - SELECT WAVEFORM... menu .......................................................... 2.331
Fig. 2-213 ARB MOD - WAVEFORM INFO menu................................................................... 2.331
Fig. 2-214 ARB MOD - DELETE WAVEFORM... menu .......................................................... 2.334
Fig. 2-215 ARB MOD - SET SMIQ ACCORDING TO WAVEFORM menu............................ 2.334
Fig. 2-216 ARB MOD - CLOCK... menu .................................................................................. 2.336
Fig. 2-217 ARB MOD - IQ OUTPUT... menu........................................................................... 2.337
Fig. 2-218 Vector modulation with an external AMIQ .............................................................. 2.338
Fig. 2-219 Menu AMIQ CTRL (presetting depends on AMIQ)................................................. 2.340
Fig. 2-220 Menu AMIQ CTRL -SETUP.................................................................................... 2.340
Fig. 2-221 Menu AMIQ CTRL -SAVE/RECALL SETTINGS... ................................................. 2.342
Fig. 2-222 Menu AMIQ - SELECT WAVEFORM/EXECUTE BATCH...................................... 2.343
Fig. 2-223 Menu AMIQ CTRL -LEVEL..................................................................................... 2.345
Fig. 2-224 Menu AMIQ CTRL - MARKER................................................................................ 2.347
Fig. 2-225 Menu AMIQ CTRL – BIT ERROR RATE TEST...................................................... 2.348
Fig. 2-226 BER Measurement ................................................................................................. 2.350
Fig. 2-227 Operating menu for BER measurement ................................................................. 2.351
Fig. 2-228 PRBS polynomials .................................................................................................. 2.357
Fig. 2-229 Block diagram of noise generator and distortion simulator..................................... 2.360
Fig. 2-230 Noise generator and distortion simulator in SMIQ.................................................. 2.360
Fig. 2-231 Menu NOISE/DIST (presetting) .............................................................................. 2.361
Fig. 2-232 Menu NOISE/DIST - POLYNOMIAL....................................................................... 2.362
Fig. 2-233 AM/AM conversion.................................................................................................. 2.364
Fig. 2-234 AM/PM conversion.................................................................................................. 2.364
Fig. 2-235 Menu LF OUTPUT (preset setting)......................................................................... 2.368
Fig. 2-236 Signal example sweep: MODE = AUTO, BLANK TIME = NORMAL..................... 2.372
Fig. 2-237 Signal example sweep: MODE = SINGLE, BLANK TIME = LONG........................ 2.372
Fig. 2-238 Menu SWEEP - FREQ............................................................................................ 2.373
Fig. 2-239 Menu SWEEP - LEVEL .......................................................................................... 2.375
Fig. 2-240 Menu SWEEP - LF GEN......................................................................................... 2.376
Fig. 2-241 Signal example LIST mode: MODE = EXT-STEP.................................................. 2.380
Fig. 2-242 Menu LIST - OPERATION page............................................................................. 2.380
Fig. 2-243 Menu List - EDIT page............................................................................................ 2.382