Rohde & Schwarz SMW-K144 - Page 61

5G New Radio Configuration and Settings
R&S
®
SMW-K144
61User Manual 1178.8013.02 ─ 06
EPRE Ratio ← PTRS Config ...
Sets the higher layer parameter epre-Ratio ratio, needed to define the ratio of PTRS
EPRE to PDSCH EPRE per layer per RE for PTRS port
The abbreviation EPRE stands for energy per resource element.
Remote command:
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTA:PTRS:EPRE on page 192
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTB:PTRS:EPRE on page 192
I_MCS_1/I_MCS_2/I_MCS_3 ← PTRS Config ...
Sets the threshold values ptrs-MCS
I
with I = {1, 2, 3} transmitted by the higher-layer
parameter timeDensity in PTRS-DownlinkConfig .
Remote command:
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTA:PTRS:MCS1 on page 192
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTA:PTRS:MCS2 on page 192
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTA:PTRS:MCS3 on page 192
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTB:PTRS:MCS1 on page 192
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTB:PTRS:MCS2 on page 192
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTB:PTRS:MCS3 on page 192
N_RB_1/N_RB_2 ← PTRS Config ...
Sets the threshold values NRB
I
with I = {0, 1} transmitted by the higher-layer parameter
frequencyDensity in PTRS-DownlinkConfig .
Remote command:
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTA:PTRS:RB0 on page 193
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTA:PTRS:RB1 on page 193
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTB:PTRS:RB0 on page 193
[:SOURce<hw>]:BB:NR5G:UBWP:USER<ch0>:CELL<st0>:DL:BWP<dir0>:
PDSCh:DMTB:PTRS:RB1 on page 193
Use PDSCH Scrambling ID
Defines the value of the variable n
ID
used for the initialization of the generator of the
PDSCH scrambling sequence.
"Off"
n
ID
= N
ID
cell
(i.e. the physical layer cell identity)
Users/BWPs Settings