Rohde & Schwarz ZNB - Page 1221

Command Reference
R&S
®
ZNB/ZNBT
1221User Manual 1173.9163.02 ─ 54
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]...................................................... 1223
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:CONTrol.........................................1223
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect........................................... 1224
[SENSe<Ch>:]SEGMent<Seg>:BWIDth[:RESolution]:SELect:CONTrol..............................1224
[SENSe<Ch>:]SEGMent<Seg>:DEFine..........................................................................1225
[SENSe<Ch>:]SEGMent<Seg>:DEFine:SELect.............................................................. 1227
[SENSe<Ch>:]SEGMent<Seg>:DELete:ALL................................................................... 1227
[SENSe<Ch>:]SEGMent<Seg>:DELete[:DUMMy]........................................................... 1228
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:CENTer?.....................................................1228
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:SPAN?........................................................1228
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STARt.........................................................1229
[SENSe<Ch>:]SEGMent<Seg>:FREQuency:STOP......................................................... 1229
[SENSe<Ch>:]SEGMent<Seg>:INSert........................................................................... 1229
[SENSe<Ch>:]SEGMent<Seg>:INSert:SELect................................................................ 1231
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]...............................................................1232
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>:POWer[:LEVel].........................................1232
[SENSe<Ch>:]SEGMent<Seg>:PORT<PortId>[:STATe]................................................... 1233
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol....................................................... 1233
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:ALL.................................................1234
[SENSe<Ch>:]SEGMent<Seg>:POWer:GAINcontrol:CONTrol..........................................1235
[SENSe<Ch>:]SEGMent<Seg>:POWer[:LEVel]:CONTrol................................................. 1236
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl...............................................................1237
[SENSe<Ch>:]SEGMent<Seg>:SWEep:DWELl:CONTrol................................................. 1237
[SENSe<Ch>:]SEGMent<Seg>:SWEep:GENeration........................................................1238
[SENSe<Ch>:]SEGMent<Seg>:SWEep:POINts.............................................................. 1239
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME.................................................................1239
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:CONTrol................................................... 1240
[SENSe<Ch>:]SEGMent<Seg>:SWEep:TIME:SUM?....................................................... 1240
[SENSe<Ch>:]SEGMent:COUNt?
Returns the number of sweep segments in the channel including all segments that are
switched off ([SENSe<Ch>:]SEGMent<Seg>[:STATe] OFF).
Suffix:
<Ch>
.
Channel number
Example:
SEGM:ADD
Create a new sweep segment no. 1 in channel no. 1 using
default settings.
SEGM OFF
Disable the measurement in the created sweep segment.
SEGM:COUN?
Query the number of segments.
Usage: Query only
Manual operation: See "Table Columns" on page 402
SCPI Command Reference