16
Feb. 2005 BR-1200CD
Reading backup user data back
into the hard disk (User Recover)
1. Insert a CD-R/RW disc containing backup user data into the BR-
1200CD’s CD-R/RW drive.
The drive’s access indicator will begin to flash. Wait until this indicator
stops flashing and turns off before proceeding.
2. Press CD-R/RW [DATA SAVE/LOAD].
The Data CD Menu screen will appear.
fig.05-520d
3. Move the cursor to RECOVER icon, and press [ENTER/YES].
Alternatively, you can press [F2] (RECOVER) if the RECOVER icon is
currently displayed.
The Recover screen will appear.
fig.05-580d
4. Press [F2] (USER).
fig.05-640d
5. Use the TIME/VALUE dial to select the data you want to recover.
If you select the data that has no backup data, “*EMPTY” will be
displayed.
Data that can be recovered:
ALL
All of the user data on the CD-R/RW disc
EFFECTS
All insert effects patches from the user bank will be recovered.
MASTERING TOOL KIT
The Mastering Tool Kit’s user bank will be recovered.
SPEAKER MODELING
The Speaker Modeling user bank will be recovered.
VOCAL TOOL BOX
The Vocal Tool Box’s user bank will be recovered.
RHYTHM
User rhythm arrangements, user drum patterns, user bass patterns, and user
loop phrases will all be recovered.
ARRANGEMENT
Only user rhythm arrangements will be recovered.
DRUM&BASS PATTERN
Only user drum patterns and user bass patterns will be recovered.
LOOP PHRASE ALL
User loop phrases from banks A through H will be recovered.
LOOP PHRASE A-H
Only user loop phrases from the selected bank will be recovered.
If you select “LOOP PHRASE A-H,” a recovery destination will appear at the
bottom of the display. If you want to change this setting, move the cursor to
“Destination” and then select a new recovery destination using the TIME/
VALUE dial.
6. When you have selected all of the data you want to recover, press [F3]
(GO).
The BR-1200CD will start the recovery process. When the message
“Complete!” appears, it indicates that the recovery has been completed
successfully.
If the hard disk contains any data of the same type as that being recovered, it
will be completely overwritten in the recovery process. As it will not be
possible to restore this data, care should be taken to ensure that important data
is not accidentally overwritten in this way.
Saving the Entire Contents of the
Hard Disk to a CD-R/RW Disc
(HDD Backup)
The BR-1200CD allows you to back up all of the data on the internal hard disk onto
CD-R/RW discs, regardless of the type of data or the song in which it is used. Data
that’s been backed up this way can later be recovered whenever needed.
Note, however, that this type of backup is limited to the data contained in the
currently selected drive or partition. If you would also like to back up data
from another drive or partition, you will need to change the current drive first.
Note also that recovered data will be stored on the currently selected drive.
1. Insert an empty CD-R/RW disc into the BR-1200CD’s CD-R/RW drive.
The drive’s access indicator will begin to flash. Wait until this indicator
stops flashing and turns off before proceeding.
2. Press CD-R/RW [DATA SAVE/LOAD].
The Data CD Menu screen will appear.
fig.05-520d
3. Move the cursor to BACKUP icon, and press [ENTER/YES].
Alternatively, you can press [F1] (BACKUP) if the BACKUP icon is
currently displayed.
The Backup Menu screen will appear.
fig.05-530d
4. Press [F3] (HDD).
The message “HDD Backup OK?” will appear.
fig.05-660d
5. Press [ENTER/YES].
The message “Write Speed?” will appear.
fig.05-560d
6. Use the TIME/VALUE dial to set the write speed.
7. Press [ENTER/YES].
If you want to cancel the backup, press [EXIT/NO].
The message “Write Sure?” will appear.
fig.05-570d
To Next Page
Loading...
