Roland GR-33 - Page 108

108
Chapter 11 Appendices
❍General Purpose #2
STATUS SECOND THIRD
BnH 11H vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value: 00H - 7FH (0 - 127) 00H-3FH=Major,
40H-7FH=Minor
* Transmitted when an external pedal is used to switch the harmony key between Major/
Minor.
❍General Purpose #3
STATUS SECOND THIRD
BnH 12H vvH
n=MIDI Channle Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value: 00H - 7FH (0 - 127)
* Transmitted the envelope data of the strings when the “PLAY FEEL” is set to
ENVELOPE1 or ENVELOPE2.
* Data is sent only in Mono mode. Transmission doesn’t take place in Poly mode.
❍General Purpose #4
STATUS SECOND THIRD
BnH 13H vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control value: 00H - 7FH (0 - 127) 00H = Reset,
01H-3FH=OFF, 40H-7FH=ON
* Transmitted the operation of onboard WAH function (Pedal 1).
❍General Purpose #6
STATUS SECOND THIRD
BnH 51H vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control value: 00H - 7FH (0 - 127) 00H-3FH=OFF,
40H-7FH=ON
* Transmitted the operation of turning ON or OFF by CTRL pedal when this channel is set
to MONO1-MONO16.
❍General Purpose #7
STATUS SECOND THIRD
BnH 52H vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value: 00H - 7FH (0 - 127) 00H-3FH=OFF,
40H-7FH=ON
* Transmitted the operation of onboard HOLD pedal when this channel is set to MONO1-
MONO16.
❍General Purpose #8
STATUS SECOND THIRD
BnH 53H vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value: 00H - 7FH (0 - 127) 00H-3FH=OFF,
40H-7FH=ON
* Transmitted the operation of CTRL pedal when the Arpeggio is held, and the HOLD
TYPE is set to Latch Type A/B.
❍General Effect #1 (Reverb Send Level)
STATUS SECOND THIRD
BnH 5BH vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value: 00H - 7FH (0 - 127)
* Transmitted the action of the EXP pedal when the EXP pedal is set to "REV SEND
LEVEL".
❍General Effect #3 (Chorus Send Level)
STATUS SECOND THIRD
BnH 5DH vvH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
vv=Control Value: 00H - 7FH (0 - 127)
* Transmitted the action of the EXP pedal when the EXP pedal is set to “CHO SEND
LEVEL”.
❍RPN MSB/LSB
STATUS SECOND THIRD
BnH 65H mmH
BnH 64H llH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
mm=Upper byte of the parameter data designated by RPN
ll=Lower byte of the parameter data designated by RPN
<<< RPN >>>
Control change includes RPN(registered parameter number), function which are defined by
the MIDI standard.
The GR-33 can transmit only one RPN: pitch bend sensitibity(RPN#0).
RPN Data entry
MSB LSB MSB LSB Function
00H 00H mmH 00H pitch bend sensitivity
The transmitted lower byte is always 00H.
* Transmitted when you change the BEND RANGE parameter on SYSTEM menu.
* Not transmitted when BEND REQ SW on SYSTEM menu is set to OFF.
●Program change
STATUS SECOND
CnH ppH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
pp=Program Number: 00H - 7FH (0 - 127) 0=prg.1 127=prg.128
●Pitch Bend Change
STATUS SECOND THIRD
EnH llH mmH
n=MIDI Channel Number: 0H - FH (0 - 15) 0=ch.1 15=ch.16
mm,ll=Value: 00H, 00H - 7FH, 7FH (-8192 - +8191)
■System Realtime Message
●Active Sensing
STATUS
FEH
* This message is always transmitted at about 270msec' interval.
■System Exclusive message
STATUS DATA BYTES STATUS
F0H iiH,ddH,.....,eeH F7H
F0H: System Exclusive
ii=ID Number: 41H (65)
dd,...,ee=Data: 00H-7FH (0-127)
F7H: EOX (End of Exclusive/System Common Message)
* For more details, refer to the page “Roland exclusive message” and Section3 or after.