Roland HP 2700 - Communication Error Message (ERR); Rejection Message (RJC)

HP-3700/2700
Dec.
1990
PEDAL
UNIT
ASSEMBLY
ASSY
22185580
(HP-2700)
ASSY
22185584
(HP-3700)
PROCEDURE
(1)/^|l||(i)
WORKING
1.
Put
(2)
on
pedal.
2. Put
(D
on
®.
3.
Fit
@
on
®.
4. Put
(D,
®,
@
and
®
on
®
and
hold
®
on
®.
3.
@^®l::#ALS-fo
4.
®.®.®.®5-®®±lc^-ti-®5-ffi‘3#li’S'fo
-NOTE
Parts of
®, ®, @
and
®
are not use from about
ZB94400
(HP-2700)
or
ZB94250
(HP-3700).
Working
4.
fit up
®
is done
at
procedure
(2).
•
hliilL
KS-2700 PEDAL UNIT
218-580
No. Part
No. Part Name
Description
pcs
22815745 KS-35
PEDAL
CHASSIS
t1.6 SPCC
(Ji«*-^S^)
1
(5) 22265422 KS-350 FELT
226422
t4
6
(D
22265512 KS-35
FELT 226-512
t3
U-=y—^7a7.
3
@
22137619 DP-7
GUIDE
213-619
PA
3
(D
22155790 BUSHING A
POM
1
©
22175228 SPRING
B
4*1.6 SWPA
1
22175227 SPRING
A
4*1.6 SWPA
1
22155791 BUSHING
B
POM
1
©
22185577 KS-35
PEDAL L
t2.6
SPCC MFCr
1
(®
22185585 KS-2700
PEDAL
CENTER t2.6
SPCC MFCr
1
22185578
KS-35 PEDAL R
t2.6 SPCC MFCr
1
KS-3700 PEDAL UNIT 218-584
No. Part
No. Part Name
Description
pcs
©
22185582
KS-3700 PEDAL
L t2.6
SPCC
1
22185581 KS-3700
PEDAL
CENTER
t2.6
SPCC
1
©
22185583 KS-3700
PEDAL
R
t2.6
SPCC
-
’IS
1
*
Parts of
(D
to
(D
are the
same
to KS-2700 PEDAL
UNIT.
*
b(i)©l5|Ip“a(i
KS-2700
•
a-
.y
h <t
®.®^@^®®®Sl^i^
fcd;^ZB94400
(HP-2700)
&t>'
ZB94250
(HP-3700)
PROCEDURE
(2)
/^HII
(2)
No. Part
No. Part Name
Description
pcs
22265482 KS-6000 FELT
226482 FELT 2
©
22175164
KS-350 COIL SPRING SWB
2
©
22205477 SENSOR
HOLDER
tO.8 SECC
3
41085143
REFLECTOR SEAL
3
©
t*tt*t*t 4x8
Binding Tapping
B1 FeCm
3
WORKING
1.
Put
®
into
@.
2.
Place
®
on
the pedal
chassis
and hold
pedals.
3.
Fit
®
to
@
and fasten by
®.
1. ®^©!cfiALSfo
3. ®7?ih*t-ro
pNOTE
Parts
®
and
@
are used
to hold the
PEDAL
R
from
about ZB94400
(HP-2700)
or ZB94250
(HP-3700).
Si5a°a®i®ti>
fcJ;^ZB94400
(HP-2700)
Rtf
ZB94250
(HP-3700)
*'f>
PEDAL
PROCEDURE
(3)
/^HII
(3)
No. Part No. Part Name
Description
pcs
23485253 HP-2700/
3700 CONNECTION
1
©
22205444 KS-35 PEDAL
HOLDER
t1.6 SECC
3
©
22285343 KS-5500
ADJUST BOLT
SS41
1
©
t$t***tt 3x6
Binding Tapping B1 FeCm
4
©
tttttttt
Screw
M4x8
FeBC w/SPW
3
WORKING
1.
Fasten
®
to the pedal
chassis.
2.
Place
®
on the
pedal
chassis.
3.
Adjust VR1, VR2 and VR3 on PCS
of connection cable.
4.
Fit
@
to
the pedal chassis.
2.
®^^4"A
•
>-!’-->
iCffi
to
3.
CONNECTION CABLE
df-
KifiS!;®VRl~VR3^-|l|^
0^1*0
4.
'
vi'-ylZ.m‘OHiftto
24