Roland HP 2700 - One-Way Communication Procedure

tone select button
progras change nusber
PIANO { 0
PIANO 2 1
HONKY TONK 2
HARPSICHORD 3
VIBRAPHONE 5
E. PIANO 6
PIANO 1 + PEANO 2 16
PIANO 1 + HONKY TONK 24
PIANO 1 + HARPSICHORD 32
PIANO 1 + VIBRAPHONE 40
PIANO 1 + E. PIANO 48
PIANO 2 + HONKY TONK 25
PIANO 2 + HARPSICHORD 33
PIANO 2 + VIBRAPHONE 41
PIANO 2 + E. PIANO 49
HONKY TONK + HARPSICHORD 34
HONKY TONK + VIBRAPHONE 42
HONKY TONK + E. PIANO 50
HARPSICHORD + VIBRAPRONE 43
HARPSICHORD + E. PLANO 5]
VIBRAPHONE + E. PIANO 53
WMChanne! Mode Message
@OMNI OFF
Status Second Third
Bn TCH OOH
n= MIDI channel number : OH - FH (0 - 15) O= cht 15 = chi6
# When power !s turned on, OMN| OFF and POLY ON are sent though the Basic Channe}.
@POLY
Status Second Third
Bou TFH OOH
n = MID] channel nuaber OH - FH (0-15) 0 = ch.1 15 = ch.16
* When power is tumed on, OMN| OFF and POLY ON are sent though the Basic Channel.
WSystem Real-Time Message
@ Active Sensing
Status
FEH
This message Is sent within a 300 ail!i_second interval.
MSystem Exclusive Message
Status deta te
FOH IIH, ddh,..... eel
FTW
Fou : system exclusive
if = (D number : 41M (65)
dd,...,ee = data : OOH-7FH (0-127)
F7H : EOX (End of Exclusive/System common)
The following message can be sent:
Brill) {ance
Reverb Mode Select ( ROOM, STAGE, HALL ON/OFF )
Temperament Select
Refer to “Roland Exclusive Message” and section 5.
When the keyboard is played while TRANSPOSE/MIDI switch is held down, both transmit
(Tx) and receive (Rx) channels are changed. Also, the transmit and recelve mode Is
set to OMNI OFF, POLY ON (MODE 3). If the Tx switch (PIANO | button) Is pressed
whlle the TRANSPOSE/M!D! switch is held down, only the transmit channe} is changed.
If the Rx switch (PIANO 2 button) is pressed while the TRANSPOSE/MIDI switch {s
held down, only the receive channel is changed.
Pressing the highest key (C8) on the keyboard while holding TRANSPOSE/MIDI switch
sets the Basic Channels ( both transmit and receive } to }, OMN1 ON and POLY ON
(MODE 1).
If the OMNI switch (HARPSICHORD button) is pressed while the TRANSPOSE/MIDI switch
is held down, MODE is set to OMNI ON and POLY ON (MODE 1). At thts tine, Basic
Channels are not changed.
key basic channel (Tx or RY) OMNI
Power-on 1 OFF
Al 1 OFF
At 1 2 OFF
Bul 3 OFF
Cc 2 4 OFF
Ce 2 5 OFF
D2 6 OFF
De 2 7 OFF
E 2 8 OFF
F 2 9 OFF
Fe 2 16 OFF
G2 1} OFF
Ge 2 12 OFF
A 2 13 OFF
At 2 14 OFF
B2 15 OFF
Cc 3 16 OFF
c 8 i] ON
4. MULTI TIMBRE MODE
Pressing the MULTI switch (VIBRAPHONE button) while the TRANSPOSE/MIDI switch ts
held down (or while receiving exclusive messages (Multi Timbre ON)) switches the HP
2700/3700 to the Multi Timbre Mode,
MChannel and Part
In the Mult! Tisbre Mode, the piano has 4 parts: each channel fs 1, 11,12 and 13.
These channel numbers are fixed. Each part channel can receive program changes
individually.
Transaitting message Is sent through the current basic channel (Tx channel). If the
basic channe! Is not set to 1,11,12 nor 13, any keyboard note is sent through
MIDI, but the note is not heard.
MNote Event
Transmitting note event !s sent through the current basic channel (Tx channel).
Receiving note event through channe! 1,11,12 or 13 1s recognized. Other channel
messages are {gnored.
BContro] Change
@Damper, Sostenuto and Soft
Damper, Sostenuto and Soft messages are sent through the basic channel (Tx
channel). ;
Receiving pedal messages through channel 1,11,12 or 33 affect each channe!
individually. These message can affect only MIDI notes.
@Volume
Volume cannot be transmitted.
Received volume messages through channel 1,11,12 or 13 affects cach channel
individually. These message can affect only MIDI notes. Volume control [ts relative
to master volume slider.
@ Brilliance
Transaitted brilliance messages are sent through the current basic channe!.
Received brilliance sessages through channel 1,11,12 or 13 affect all the
Part notes and keyboard notes.
The lasi control message the from panel brilliance silder or the last MID! message
has priority.
27