Roland JX-10 - Individual Tone Parameters (IPR)

JX-10 MIDI IMPLEMENTATION
Manual Version 3.21
Page. 54 of 73
Key mode values
Param 18 Param33 Key mode
00H 00H Dual
01H 00H Split
02H 00H Whole Upper
03H 00H Whole Lower
00H 01H X-Fade
00H 02H T-Voice
INDIVIDUAL TONE PARAMETERS (IPR)
A B C D E F G H I J
F0H 41H 36H mcH 24H 20H toneH prmH valH F7H
A = Exclusive message start
B = Roland ID
C = Operation code IPR
D = MIDI channel (mcH) 00H to 0FH (1 to 16 decimal)
E = JX10 Format
F = Level 1 Tone
G = (toneH) Group number 01H = Upper tone 02H = Lower tone
H = (pmH) Parameter 00H-32H (0-51 decimal)
I = (valH) Value 00H-F7H (0-127 decimal)
J = End of Exclusive message
Parameter (pmH) Value (valH)
00H-009H Tone name (10 char) In ASCII Format
0BH DCO1 Range 00H=16` 20H=8` 40H=4` 60H=2`
0CH DCO1 Waveform 00H= Noise 20H= Saw 40H= Pulse 60H= Square
0DH DCO1 Tune 00H-F7H (0-127 decimal)
0EH DCO1 LFO mod depth 00H-F7H (0-127 decimal)
0FH DCO1 Env mod depth 00H-F7H (0-127 decimal)
10H DCO2 Range 00H=16` 20H=8` 40H=4` 60H=2`
11H DCO2 Waveform 00H= Noise 20H= Saw 40H= Pulse 60H= Square
13H DCO2 Tune 00H-F7H (0-127 decimal)
14H DCO2 Fine tune 00H-F7H (0-127 decimal)
15H DCO2 LFO mod depth 00H-F7H (0-127 decimal)
16H DCO2 Env mod depth 00H-F7H (0-127 decimal)
12H DCO X-mod 00H= OFF 20H= Sync1 40H= Sync2 60H= Xmod
1AH DCO Dynamics 00H= OFF 20H= Dyn1 40H= Dyn2 60H= Dyn3
1BH DCO Env mode 00H= Env2- 20H=Env2+ 40H= Env1- 60H= Env1+
1CH DCO1 Level 00H-F7H (0-127 decimal)
1DH DCO2 Level 00H-F7H (0-127 decimal)
1EH Mix Env depth 00H-F7H (0-127 decimal)
1FH Mix Dynamics 00H= OFF 20H= Dyn1 40H= Dyn2 60H= Dyn3
20H Mix Env mode 00H= Env2- 20H=Env2+ 40H= Env1- 60H= Env1+
21H HPF Cuttoff 00H= 0 020H= 1 040H= 2 060H= 3
22H LPF Cuttoff 00H-F7H (0-127 decimal)
23H Resonance 00H-F7H (0-127 decimal)
24H VCF LFO Depth 00H-F7H (0-127 decimal)
25H VCF Env Depth 00H-F7H (0-127 decimal)
26H VCF Key follow 00H-F7H (0-127 decimal)
27H VCF Dynamics 00H= OFF 20H= Dyn1 40H= Dyn2 60H= Dyn3
28H VCF Env mode 00H= Env2- 20H=Env2+ 40H= Env1- 60H= Env1+