Roland RD-600 - Page 68

O RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte 3rd byte
BnH 65H mmH
Bn oth UH
o = MIDI channet number: OF-FH (ch.t-ch.16)
mm = upper byte of parameter number specified by RPN
I= lower byte of parameter number specitied by RPN
On the RD-600, RPN can be used to modity the following parameters,
RPN Data entry
MSBLSB = =MS5BLSB Explanation
QOH GOH mmH-— Pitch Bend Sensitivity
mm: 0OH-18H (0-24 semitones)
Ul: OOH
specify up to 2 octaves in semitone steps
OOH O1H mmH ilH Master Fine Tuning
man, fh 20 00H - 40 OOH - 60 OOH (-50 - 0 - +50 cents)
OUH 02H mmbHi-—~ Master Coarse Tuning
mm: 10H-40H-70H (48 - 0 - +48 semitones)
tl: 00H
7FH 7FH — see RPN null
@ Program Change
Status 2nd_byte
CnH ppH
OH-FH (ch.1-ch.16)
O0H-7FH (prog.1-prog.128)
n= MIDI channel number:
pp = Program number:
®@ Pitch Bend Change
Status And byte Sed byte
EnH WH mmH
OH-FH (ch. f-ch.16)
OO OOF - 40 OOH - 7PF 7FH (-8192 - 0 - +8191)
n= MIDI channel number:
mum, Il = Pitch Bend value:
m System Realtime Message
@ Active sensing
Status
FEH
* This will be transmitted constantly at intervals of approximately 250 ms.
@ System exclusive messages
“Identity Reply” and “Data Set 1 (DT1)” are the only System Exclusive messages transmit-
ted by RD-600.
When an appropriate “Identity Request Message” and “Data Request 1 (RQ1)” message
are received, the requested internal data will be transmitted.
‘D Identity Reply
us Databyle Status
POH 7EH, dev, 06H, 02H, 41H, 09H, 01H, OOH, OOH, OOH, 01H, 00H, OOH, F7H
Byte Explanation
FOH Exclusive status
7EH (D number (universal non-realtime message)
dev Device ID (use the same as the device ID of Roland)
06H Sub ID#1 (General Information)
O2H Sub ID#2 (identity Reply)
41H 1D number (Roland)
09H Device family code (LSB)
O1H Device family code (MSB)
OOF Device family number code (LSB)
OOH Device family number code (MSB)
OOH Software revision level
01H Software revision level
UH Software revision level
OUH Software revision level
F7H EOX (End of Exclusive}
* Keply the message by Uie unique device 1D (dev} when the device has received the
“Identity Request Message” in the Broadcast
D Data set 1 oT
Status Data byte Status
FOH 4H, dev, OOH, 09H, 12H, aaH, bbH, ccH, dd, eeH. ... fH. sum F7H
Byte Explanation
FGH Exclusive status
41H ID number (Ryland)
dev Device ID (dev: 1GH-1FH, Initial value is 10H)
OOH Model ID (RD-600)
08H Model ID (RD-600)
12H. Camumand [D (DT1)
aaH Address MSB: upper byte of the starting address of the data to be sent
bbH Address
cH Address
ddH Address LSB: lower byte of the starting address of the data to be sent.
eeH Data: the actual data to be sent.
Hl Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data,
and data will be transmitted from the specified starting address and size. Refer to the
Address and Size given in Section 3 (page 68).
* Data farger than 128 bytes will be divided into packets of 128 bytes or less, and each
packet will be sent at an interval of about 40 ms
* Regarding the checksum please refer to page 72.
Section 3. Parameter Address Map (Model
ID = 00H 09H)
This map indicates address, size, Data (range), Parameter, Description, and Default Value
of parameters which can be transferred using “Request data 1 (RQI)” and “Data set |
(DT}).”
All the numbers of address, size, Data, and Default Value are indicated in 7-bit
Hexadecimal-torm.
@ Parameter Address Block
RD-600 < MODEL ID = 00 09H >