Roland TR-6S - KIT: MASTER FX

3
KIT Parameters
KIT: MASTER FX
Parameter Value Explanation
Type
HPF, LPF, LPF/
HPF, H BOOST,
L BOOST,
L/H BOOST,
ISOLATOR,
TRANSIENT,
TRANSIENT2,
COMPRESSOR,
DRIVE,
OVERDRIVE,
DISTORTION,
FUZZ, CRUSHER,
PHASER,
FLANGER, SBF,
NOISE
Selects the type of MASTER FX.
HPF: high pass filter
(cuts the low-frequency region)
LPF: low pass filter (cuts the high-frequency region)
LPF/HPF: low pass filter / high pass filter
(cuts the high-frequency or low-frequency region)
H BOOST: high boost (boosts the highfrequency
region)
L BOOST: low boost (boosts the low-frequency
region)
L/H BOOST: low boost / high boost (boosts
the low-frequency or high-frequency region)
ISOLATOR: adjusts the balance of the low,
mid, and high-frequency regions.
TRANSIENT: strengthens or weakens the
attack and release.
TRANSIENT2: uses the attack and release
to operate a filter.
COMPRESSOR: compresses loud input,
making the maximum levels more
consistent.
DRIVE: uncolored distortion.
OVERDRIVE: overdrive
DISTORTION: distortion
FUZZ: fuzz
CRUSHER: produces a lo-fi effect.
PHASER: produces a phase effect.
FLANGER: produces a flanging effect.
SBF: side band filter
(a filter that passes only specific
frequency components)
.
NOISE: adds noise.
Sw
MASTER FX
[ON]
OFF, ON Turns the MASTER FX effect ON/OFF.
Ctrl
[KIT]+ MASTER FX
[CTRL]
Selects the parameter that is controlled by the MASTER FX
[CTRL] knob.
(HPF) Depth, Resonance
(LPF) Depth, Resonance
(LPF/HPF) Depth, Resonance
(H BOOST) Boost, Frequency
(L BOOST) Boost, Frequency
(L/H BOOST) Boost, Frequency
(ISOLATOR) Balance, Low, Mid, High
(TRANSIENT) EnvDepth, Attack, Release
(TRANSIENT2) EnvDepth, Attack, Release
(COMPRESSOR) Balance, Attack, Release
(DRIVE) Balance, Drive, Level, HpFreq, PreEqFreq, PreEqL,
PreEqH, PostEqFreq, PostEqL, PostEqH
(OVERDRIVE) Balance, Drive, Tone, Level
(DISTORTION) Balance, Drive, Tone, Level
(FUZZ) Balance, Drive, Tone, Level
(CRUSHER) Balance, SmplRate, Filter
(PHASER) Balance, Rate, Depth, Resonance, Manual
(FLANGER) Balance, Rate, Depth, Resonance, Manual
(SBF) Balance, BandIntrvl, BandWidth
(NOISE) Color, Level
HPF
Depth
MASTER FX [CTRL] *1
0–255
Specifies the cutoff frequency.
Raising the Depth raises the cutoff
frequency, deepening the HPF effect.
Resonance
MASTER FX [CTRL] *1
0–255 Specifies the amount of resonance.
Type
-24dB, -18dB,
-12dB
Specifies the filter type.
Gain
-40dB–0dB–
+40dB
Specifies the output gain of the filter.
Parameter Value Explanation
Clipper
OFF, ON
Turn this ON if you want to prevent
excessive volume from occurring when
Resonance is raised.
LPF
Depth
MASTER FX [CTRL] *1
0–255
Specifies the cutoff frequency.
Raising the Depth lowers the cutoff
frequency, deepening the LPF effect.
Resonance
MASTER FX [CTRL] *1
0–255 Specifies the amount of resonance.
Type
-24dB, -18dB,
-12dB
Specifies the filter type.
Gain
-40dB–0dB–
+40dB
Specifies the output gain of the filter.
Clipper
OFF, ON
Turn this ON if you want to prevent
excessive volume from occurring when
Resonance is raised.
LPF/HPF
Depth
MASTER FX [CTRL] *1
LPF 127–FLAT–
HPF 127
Specifies the cutoff frequency.
Lowering the Depth (toward LPF) produces an
LPF effect, lowering the cutoff frequency.
Raising the Depth
(toward HPF) produces an
HPF effect, raising the cutoff frequency.
Resonance
MASTER FX [CTRL] *1
0–255 Specifies the amount of resonance.
Type
-24dB, -18dB,
-12dB
Specifies the filter type.
Gain
-40dB–0dB–
+40dB
Specifies the output gain of the filter.
Clipper
OFF, ON
Turn this ON if you want to prevent
excessive volume from occurring when
Resonance is raised.
H BOOST
Boost
MASTER FX [CTRL] *1
0–255 Adjusts the amount of boost.
Frequency
MASTER FX [CTRL] *1
0–255
Boosts the region above the specified
frequency.
Gain
-40dB–0dB–
+40dB
Specifies the output gain.
L BOOST
Boost
MASTER FX [CTRL] *1
0–255 Adjusts the amount of boost.
Frequency
MASTER FX [CTRL] *1
0–255
Boosts the region below the specified
frequency.
Gain
-40dB–0dB–
+40dB
Specifies the output gain.
L/H BOOST
Boost
MASTER FX [CTRL] *1
LOW 127–FLAT–
HIGH 127
Adjusts the amount of boost.
Lowering the Boost (toward LOW) boosts the
low-frequency region.
Raising the Boost
(toward HIGH) boosts the
high-frequency region.
Frequency
MASTER FX [CTRL] *1
0–255
The region below or above this frequency
is boosted.
Gain
-40dB–0dB–
+40dB
Specifies the output gain.