Roland V-Drums TD-50 - Delay; Tape Echo; Reverse Delay; 3 Tap Pan Delay

35
Multi-Eect Parameters
DELAY
This is a stereo delay.
Parameter Value Explanation
Tempo Sync Left,
Right
OFF, ON
Species whether the delay time
value of the left/right delay sounds
is specied as a note value (ON) or
not (OFF).
Delay Left, Right
Time
1–1300 ms, note
Delay time from the original sound
until the left/right delay sound is
heard
Phase Left, Right NORMAL, INVERSE Phase of the delay sound
Feedback Mode NORMAL, CROSS
Selects the way in which delay sound
is fed back into the eect
NORMAL: The left/right delay sounds
are fed back without modication.
CROSS: The left/right delay sounds
are alternately exchanged when fed
back.
Feedback -98–+98 %
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative “-” settings will invert the
phase.
HF Damp
200–8000
Hz, BYPASS
Adjusts the frequency above which
sound fed back to the eect is
ltered out. If you don’t want to lter
out any high frequencies, set this
parameter to BYPASS.
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Level 0–127 Output Level
TAPE ECHO
A virtual tape echo that produces a realistic tape delay sound. This
simulates the tape echo section of a Roland RE-201 Space Echo.
Parameter Value Explanation
Mode
S, M, L, S+M, S+L,
M+L, S+M+L
Combination of playback heads to
use Select from three dierent heads
with dierent delay times
S: Short
M: Middle
L: Long
Repeat Rate 0–127
Tape speed
Increasing this value will shorten the
spacing of the delayed sounds.
Intensity 0–127 Amount of delay repeats
Bass -15–+15 dB
Boost/cut for the lower range of the
echo sound
Treble -15–+15 dB
Boost/cut for the upper range of the
echo sound
Head S Pan L64–R63
Independent stereo location for the
short, middle, and long playback
heads
Head M Pan L64–R63
Head L Pan L64–R63
Tape Distortion 0–5
Amount of tape-dependent
distortion to be added
This simulates the slight tonal
changes that can be detected by
signal-analysis equipment. Increasing
this value will increase the distortion.
W/F Rate 0–127
Speed of wow/utter (complex
variation in pitch caused by tape
wear and rotational irregularity)
W/F Depth 0–127 Depth of wow/utter
Level 0–127 Output level
REVERSE DELAY
This is a reverse delay that adds a reversed and delayed sound to
the input sound. A tap delay is connected immediately after the
reverse delay.
Parameter Value Explanation
Threshold 0–127
Volume at which the reverse delay
will begin to be applied
Tempo Sync Rev OFF, ON
Species whether the delay time
value of the reverse delay is specied
as a note value (ON) or not (OFF).
Rev Delay Time 1–1300 ms, note
Delay time from when sound is input
into the reverse delay until the delay
sound is heard
Rev Delay
Feedback
-98–+98 %
Proportion of the delay sound that
is to be returned to the input of the
reverse delay.
Negative “-” settings will invert the
phase.
Rev Delay HF
Damp
200–8000 Hz,
BYPASS
Frequency at which the high-
frequency content of the
reverse-delayed sound will be cut
(BYPASS: no cut)
Rev Delay Pan L64–63R
Stereo location of the reverse delay
sound
Rev Delay Level 0–127 Volume of the reverse delay sound
Tempo Sync
Delay 1–3
OFF, ON
Species whether the delay time
value of the tap delay is specied as a
note value (ON) or not (OFF).
Delay 1–3 Time 1–1300 ms, note
Delay time from when sound is input
into the tap delay until the delay
sound is heard
Delay 3 Feedback -98–+98 %
Proportion of the delay sound that
is to be returned to the input of the
tap delay (negative values invert the
phase)
Delay HF Damp
200–8000 Hz,
BYPASS
Frequency at which the high
frequency content of the tap delay
sound will be cut (BYPASS: no cut)
Delay 1 Pan,
Delay 2 Pan
L64–63R
Stereo location of the tap delay
sounds
Delay 1 Level,
Delay 2 Level
0–127 Volume of the tap delay sounds
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Level 0–127 Output Level
3TAP PAN DELAY
Produces three delay sounds; center, left and right.
Parameter Value Explanation
Tempo Sync Left,
Right, Center
OFF, ON
Species whether the delay time
value of the left/right/center delay
sound is specied as a note value
(ON) or not (OFF).
Delay Left, Right,
Center Time
1–2600 ms, note
Adjusts the time until the delay
sound is heard.
Center Feedback -98–+98 %
Adjusts the amount of the delay
sound that’s fed back into the eect.
Negative “-” settings invert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the eect is
ltered out. If you do not want to
lter out any high frequencies, set
this parameter to BYPASS.
Left, Right,
Center Level
0–127 Volume of each delay
Low Gain -15–+15 dB Gain of the low frequency range
High Gain -15–+15 dB Gain of the high frequency range
Level 0–127 Output Level