Roland VS-1680 - Three Insert Effect Examples

102
Chapter 7 Using Internal Effects (VS8F-2)
not appear above [F1], press [PAGE] a few times until
you see “Ef1In”, and then press [F1 (Ef1In)].
3. Press [YES].
4. Use [ ] and [ ] to move the cursor to the Effect
you want to insert. Use the TIME/VALUE dial to select
the desired setting for Effect Insert Switch.
EFX1(Effect Insert Switch)
This sets how the effect is connected.
Off:
The channel is not routed into the effect.
Ins:
The channel is routed into both channels of the stereo
effect.
Snd (Insert Send Level)
This adjusts the level of signal (-42 dB to +6 dB) sent to
the effect. The default setting is 0 dB.
Rtn (Insert Return Level)
This adjusts the level of signal (-42 dB to +6 dB) returned
from the effect. The default setting is 0 dB.
5. Press [PLAY (DISPLAY)] to return to the Playlist display.
Insert EFX2-EFX 4 into the MIX bus using the same steps.
Three Insert Effect Examples
Example 1: Process a Recorded Guitar
Solo Through a Guitar Amp Simulator.
General Strategy: Insert the effect in the Track Mixer.
Details for this Example: Select Patch P088 as EFX1, Insert
on Track 3.
Begin by Selecting the Effect
1. Press [PLAY (DISPLAY)].
2. Hold [SHIFT] and press [F3 (EFFECT A)].
3. Press [F1 (EFX1)]. The Effect 1 screen appears in the
display. If “EFX1” does not appear above [F1], press [F6
(EXIT)] until it does. Then, press [F1 (EFX1)].
4. Press [F2 (Sel)]. The effects list appears in the display.
5. Use the TIME/VALUE dial or [ ], [ ], [ ],
and [ ] to move the cursor to Effect Preset Patch P088
“GuitarMulti1.”
6. Press [F4 (Exec)] or press [YES] to select the effect. The
EFFECT 1 screen appears in the display.
Next, Set up the Mixer
1. Press the SELECT button for Track 3. The button
indicator lights, and the Track Mixer Screen appears in
the display.
2. Use [ ], [ ], [ ], and [ ] to move the
cursor to “EFXIns,” or, press [F1 (Ef1In)]. If “Ef1In” does
not appear above [F1], press [PAGE] a few times until
you see “Ef1In”, and then press [F1 (Ef1In)]. This will
move the cursor directly to “EFXIns.”
3. Press [YES].
4. Use [ ] and [ ] to move the cursor to EFX1. Use
the TIME/VALUE dial to change the Effect Insert Switch
to “Ins.”
5. Press [PLAY (DISPLAY)] to return to the Playlist display.
Example 2: Use a Microphone
Simulator on a Vocal Track to be
Recorded.
General Strategy: Insert the effect in the Input Mixer.
Details for this Example: Select Patch P128 as EFX3, insert
on Input 2.
Begin by Selecting The Effect:
1. Press [PLAY (DISPLAY)].
2. Hold [SHIFT] and press [F4 (EFFECT B)].
3. Press [F1 (EFX3)]. The Effect 3 screen appears in the
display. If “EFX3” does not appear above [F1], press [F6
(EXIT)] until it does. Then, press [F1 (EFX3)].
4. Press [F2 (Sel)]. The effects list appears in the display.
5. Use the Time/VALUE dial or [ ], [ ], [ ],
and [ ] to move the cursor to Effect Preset Patch P128
“DR20 -> 87.”
6. Press [F4 (Exec)] or press [YES] to select the effect. The
EFFECT 3 screen appears in the display.
Icon
Patch Name