Roland XP-10 - Page 85

Chapter 12. Appendix
@ Individual Porameters
Individual Parameter Transmission transmits dala {or requests data) Jor one parameter as one exclusive message {one packet of “FO ..... F7").
In Individual Parameter Transmission, you must use the Address and Size listed in the following “Parameter Address Map”. Addresses marked at "# cannot be used as starting addresses.
<GS (Model 1D=42H) >
@ System Parameters
Parameters related to the system of the device are called System Parameters
Address(H) Size{H) DatatH) ameter Description Default Value (H) Description
400000 00.0004 O18 - OVER MASTER TUNE 100.6 - 100.0 foent} 06.04 00:00 O {cent}
40 00 018 Use nibblized data.
40 00 024
A 00 O38
* Refer to section 4. Supplementary maicrial, “About tuning"(Page 91).
400004 000001 10 -7F MASTER VOLUME 0-127 TF 127
{= FO 7F 7F 04.01 00 wy F7 )
400005 O00081 28-58 MASTER KEY-SHIFT -24 - +24 [semitones] 40 Olsemitones}
400006 000001 01-7F MASTER PAN -63 (LEFT) - +63 (RIGHT) 40 0} (CENTER)
40007F 000001 oO MODE SET 00 ~ GS Reset
(Rx. only} 127 = Exit GS
* Refer to “System exclusive messages related to Mode settings {Page 81).
400110 60:00:10 00- 1BH VOICE RESERVE Part 10(Drum Part) 2 2
4001 114 Part} 06 6
4001 12e Part 2 42 2
4001 134 Part 3 a2 2
400) 14e Partd 02 2
A001 158 Part 5 02 2
40 01 168 Part & 02 2
4001 178 Part7 02 2
4001 18H Fart 8 02 2
40 01 198 Part? 02 2
a0 OT LAW Part 1? 00 0
4001 #
40 01 LF8 Part 16 00 0
* The sum trtal of voices in the voice reserve function must be equat to or less than the number of the maximum polyphony. The maximum polyphony of the XP-30 is 28, For compatibility with other
GS madels, it is recommended thal the maximum polyphony be equal or Jess than 28.
4001 30 o0ne01 1-07 REVERB MACRO 00: Room 1 4 Hail 2
01: Room 2
02: Room 3
03: Hall 1
04: Hall 2
05; Plate
06: Delay
07: Panning Delay
400131 0000 03 00-07 REVERB CHARACTER 0-7 OF 4
4001 32 00.0001 00-07 REVERB PRE-LPF 0-7 90 0
400133 00001 00 - 7F REVERB LEVEL Q- 127 40 4
0134 on 0001 00-7F REVERB TIME 0-127 40 64
400135 oo 0001 00 - 7F REVERB DELAY FEEDBACK 0-127 ™ 0
4001 36 000001 00-7F REVERB SEND LEVEL TO CHORUS 0-127 0 0
* REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverh parameter will be set to the most suit-
able value.
* REVERB CHARACTER is a parameter that changes the reverb algorithm, The value of REVERB CHARACTER corresponds fo (he REVERB MACRO of the same number.
4001 38 000001 00-07 CHORUS MACRO 00: Chorus 1 ir Chorus 3
01: Chorus 2
02: Chorus 3
03: Chorus 4
(04: Feedback Chorus
05: Flanger
06: Short Delay
07: Short Delay (FB)
400139 00.00 01 00-07 CHORUS PRE-LPF 0-7 tue 0
4001 3A 00.0001 00 -7F CHORUS LEVEL 0-127 wv 64
40 01 3B 00.00 0f 00 -7F CHORUS FEEDBACK 0-127 18 B
MOT IC 00 00 MT 00-7F CHORUS DELAY 0-127 SD 80
4001 3D 600001 00 -7F CHORUS RATE 0-127 03 3
4001 3E 000001 00-7F CHORUS DEPTH 0-127 iB 19
4001 3F 00000) 0-7F CHORUS SEND LEVEL TO) REVERB 0 - 127 oO 0
* CHORUS MACRO is a macro parameter that allows global setting of chorus parameters. When you use CHORUS MACRO to select the chorus type, cach chorus parameter will be set to the most
suitable value.
85