Roland XP-10 - Page 86

Chapter 12. Appendix
ES A ro IN Sc I aS 1 a a DP NR ON ERE RPE a POP aE Oe PE ee OD
@ Part Parameters
XP-10 has 16 parts, Parameters that can be set individually tor each Part arr called Part parameters.
Hf you use exclusive messages to set Parl parameters, specify the address by Block number rather than Part Number (normally the same number as the MIDI channel). The Block number can be specified as one of 16 blocks, fram
OH) to F(H).
The relation between Part number and Block number is as follows.
x. .BLOCK NUMBER (0 - F},
Part 1 (MIDI ch = 1) x51
Part 2 (MIDI ch = 2) x=2
Part 9 (MIDI ch = 9} x=9
PartlU (MIDI ch =10) x=0
Part) (MIDI ch =11) x=A
Parth2 (MIDI ch #12) x=8
Partl6 (MIDE ch =16) x=F
Address(H) Size(H) Data(H) Parameter Description Default Value (H) Descrip!
40:1x 00 000002 00-7F TONE NUMBER CC#OO VALUE 0 - 127 00 6
40 1s O18 00-7F P.C. VALUE 1-128 oo 1
40 1x 02 000001 © -10 Rx. CHANNEL 1-16,OFF Same as the Part Number
40 1x 03 00.0001 00 - OF Rx. PITCH BEND OFF / ON Ol ON
4 1x 04 00:00:01 00-01 Rx. CH PRESSURE(CAS) OFF / ON OL ON
40 1x 05 0000 01 00-01 Rx. PROGRAM CHANGE OFF / ON OL ON
40 1x 06 00.0001 00 - OF Rx. CONTROL CHANGE OFF / ON Or ON
40 1. 07 00.0001 00-01 Ra, POLY PRESSURE(PAA, OFF / ON o1 ON
401 O8 000001 O-01 Rx. NOTE MESSAGE OFF / ON 01 ON
40 1x 09 00 0001 00-01 Rx. RPN OFF / ON 0} ON
401% 0A. 00 00:01 00-01 Rx. NRPN OFF / ON O0(61*) OFF(ON*)
* Rx. NRPN is set to OFF by power-on or by receiving “Turn General MIDI System: On”, and it will be set ON when "GS RESET’ is received
401K OB 00.0001 00-01 Rx. MODULATION OFF / ON o1 ON
40 1x 0C 00.00 01 00-01 Rx. VOLUME OFF / ON 01 ON
401%0D 0.0001 oo-01 Rs. PANPOT OFF / ON 1 ON
40 1x OE 00 0001 00-01 Rx. EXPRESSION OFF / ON On ON
40 1x OF 00.0001 00-01 Rx. HOLDI OFF / ON ol ON
40: 1x 10 00.0001 00-01 Rx. PORTAMENTO OFF / ON OL ON
401% 11 000001 00-08 Rx. SOSTENUTO OFF / ON 01 ON
Wx 12 0000 01 00-01 Rx. SOFT OFF / ON ul ON
401% 13 000001 00-01 MONO/POLY MODE Mano / Poly or Poly
(=CC# 126 01 / CC# 127 00)
40 1x 14 0001 00 - 02 ASSIGN MODE 0 = SINGLE OG at xo) SINGLE at x=)
1 sLIMITED-MULT} Ol at x¥0 LIMITED-MULTI at x¥0
2 FULL-MULTI
* ASSIGN MODE is the parameter that determines how voice assignment will be handled when sounds overlap on identical note numbers in the same channel (i.e, repeatedly struck notes), This is initial-
ized to a mode suitable for each Part, so for general purposes there is nv need to change this.
401x158 000001 00 - 02 USE FOR RHYTHM PART 0 <= OFF OO at x¥0 OFF at x40
1=MAPI O1 at x=0 MAP} at x¥0
2=MAP2
* This parameter sets the Drum Map of the Part used as the Drum Part. XP-10 can simultaneously (in different Parts) use up to two Drum Maps (MAP, MAP2). With the initial settings, ParttO (MIDI
CH#10, x=) is set to MAP1 (1), and other Parts are sct to normal instrumental Parts (OFF(0)).
AU 1x 16 00.00 01 28 - 5B PITCH KEY SHIFT -24 - +24 [semitones] 40 0 [semitones]
40 1x 17 00.00 02 08 - FB PITCH OFFSET FINE 12.0 - +12.0 [Hz] 08 UO (Hz)
40 1x 18H Use nibblized data.
“PITCH OFFSET FINE allows you to alter, by a specified frequency amount, the pitch at which notes will sound. This parameter differs from the conventional Fine Tuning (RPN #1) parameter in that the
amount of frequency alteration (in Hertz) will be identical no matter which note is played. When a multiple number of Parts, each of which has been given a different setting for PITCH OFFSET FINE, are
sounded by means of an identical note number, you can obtain a Celeste effect.
40 1x 19 0000 01 00 -7F PART LEVEL 0-127 64 100
{2CC#7)
ax lA 000001 00-7F VELOCITY SENSE DEPTH 0-127 40 64
40 ix 1B 000001 00-7F VELOCITY SENSE OFFSET 0-127 40 of
a0 1K CE OU 000 OO -7F PART PANPOT -64(RANDOM), wo O(CENTER)
(=CC# 10, except RANDOM) -63{LEFT) - +63{RIGHT)
41x ID 000001 QO -7F KEY RANGE LOW {C-1) - (G9) 00 Cl
4018 TE 00001 00-7F KEY RANGE HIGH {C-1) - (G9) 7F GY
40 Ux TF 000001 00 -5F CC] CONTROLLER NUMBER 0-95 10 6
40 1x 20 000007 00 -5F CC2 CONTROLLER NUMBER 0-95 it Vv
41x 21 00001 OO-7F CHORUS SEND LEVEL 0-127 oo a
(=CC# 93)
40 1x 22 00 0003 00 - 7F REVERB SEND LEVEL 0-127 28 Ww
(=CC# 91)
40 tx 23 00.0001 00 - 01 Rx. BANK SELECT OFF / ON B1(00") ON(OFF*)
“Rx, BANK SELECT is set to ON by power-on or by receiving “GS RESET”, and will be set OFF when “Turn General MIDI System On‘is received.
40x 3G OOO OI OE - 72 TONE MODIFY 1 “50 - +50 40 8
Vibrato rate (=> NRPN# 8)
40 1x31 000001 UE - 72 TONE MODIFY 2 50 - +50 40 vu
Vibrato depth (= NRPN¢ 9)
40 tx 32 00.0001 OE - 50 TONE MODIFY 3 -H- +16 40 o
TVF cutoff frequency (= NRPNE# 32)
40 1x33 000001 OE - 72 TONE MODIFY 4 -BO- +50 9
TVF resonance {=NRPN# 33)
40x CODG01 UE -72 TONE MODIFY 5 +50 - +50 8
TVFRTVA Env.attack (>NRPN# 99}
401x535 000001 OE - 72 TONE MODIFY 6 -50-+50 40 6
TVF&TVA Eny.decay (=NRPN¢# 100)
401x356 000001 UE-72 TONE MODIFY 7 BW - +50 o
TVF&TVA Env. release (= NRPN@ 192}
40 1x 37) OO 000) OE-72 TONE MODIFY 8 50. +50 o
86
Vibrate delay (=NRPN&# 10)