107
Chapter 6
Chapter 6 Other Settings/Status Checks
Setting Procedure:
1.
Press [SYSTEM] to make its indicator light.
2.
Press [ CURSOR] a few times to move the cursor to the parameter group in the upper line of the display.
3.
Turn [VALUE] to choose the parameter group containing the parameter you wish to set up.
4.
Press [CURSOR ] to move the cursor to the parameter name in the lower-left corner of the screen.
5.
Turn [VALUE] to choose the parameter you wish to set.
6.
Press [CURSOR ] to move the cursor to the selected parameter’s value.
7.
Turn [VALUE] to choose the desired value.
8.
Press [EXIT] to return to the previous screen.
Making Overall Settings
By holding down [SHIFT] and pressing [SYSTEM], you can move directly to the LCD Contrast screen.
Selecting Common Controllers
These settings allow you to choose four MIDI controllers for global use when controlling the parameters of any Patch or Performance. The settings
in each Patch or Performance will determine whether the two controllers you choose here will actually be used. In each Patch or Performance, you
will also need to specify the parameters to be controlled.
Parameter
Value Description
GENERAL
LCD Contrast
1–10 This adjusts the contrast/brightness of the display. Higher values will make the characters darker.
PowerUp Mode LAST-ST,
DEFAULT
Sets the condition of the XV-5050 when its power is turned on.
LAST-ST:
The XV-5050 will power up exactly as it was when it was turned off.
DEFAULT:
The XV-5050 will be ready to play Patch “US:001.”
Master Level 0–127 Adjusts the volume of the entire XV-5050.
Clock Source System Clock
Source
INT, MIDI,
USB
Specifies the tempo clock of the system.
INT:
The internal clock
MIDI:
An external clock received via MIDI IN connector
USB:
An external clock received via USB connector
System Tempo 20–250 Sets the system tempo. * When Clock Source is set to “MIDI” or “USB,” the tempo will synchronize to the
clock messages received from an external device, so the tempo value will be ignored.
Mix/Parallel Output Mix/
Parallel
MIX,
PARALEL
MIX:
Signals that are set to be output from jacks other than the A (MIX) OUTPUT jacks are mixed and output
from the A (MIX) OUTPUT jacks.
This setting allows you to quickly route everything through headphones when you are creating sounds,
or to combine all of your sounds into two outputs when sending the XV-5050’s signal to a mixer that has
only two channels. When MIX is selected, sound routed to the INDIVIDUAL OUTPUT 3 jack is sent to the
left A (MIX) OUTPUT jack, and sound routed to the INDIVIDUAL OUTPUT 4 jack are sent to the right A
(MIX) OUTPUT jack.
PARALEL:
Sounds are routed to output jacks according to their output settings.
Patch Remain Patch Remain
Switch
OFF, ON This specifies whether you want the notes that are sounding to remain (ON) or turn off (OFF) when you select
a new Patch or Rhythm Set in Patch mode. In addition, when “ON” is selected, the Volume and Pan data, and
the Key Mode and other settings received via MIDI (CC 5, 7, 10, 65, 68, 71–74, RPN 0, 1, 2, MONO ON, POLY
ON) are passed on.
Rhy EditKey Rhythm Edit
Key
PANEL,
PNL&MIDI
You can set whether you’ll be able to select percussion instruments for editing only by pressing the XV-5050’s
front-panel buttons or also by pressing keys on a connected MIDI keyboard.
PANEL:
Percussion instrument sounds can be selected only by using the XV-5050’s TONE SELECT [1]–[4].
PNL&MIDI:
Percussion instrument sounds can be selected using the XV-5050’s TONE SELECT [1]–[4] and
by pressing a key on a connected MIDI keyboard.
Output Gain -12, -6, 0, +6,
+12 dB
This adjusts the output gain from the XV-5050’s Analog Out and Digital Out. When, for example, there are
relatively few voices being sounded, boosting the output gain can let you attain the most suitable output level
for recording and other purposes.
Parameter
Value Description
CONTROL
Sys Ctrl Src1–4
System Control
Source 1–4
OFF, CC01–31, 33–95, BEND, AFTER
OFF:
No controller is used.
CC01–95:
Controller numbers 1–95 (except for 32)
BEND:
Pitch Bend
AFTER:
Aftertouch
XV-5050_e.book 107 ページ ２００３年６月２７日 金曜日 午後３時１４分
To Next Page
Loading...