Roller Control User Manual

5. Disposal
The hand pressure testing pump may not be thrown into the domestic waste
at the end of use. It must be disposed of properly by law.
6. Manufacturer’s Warranty
The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which ROLLER is not responsible, shall be excluded from the
warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station authorized by ROLLER
without prior interference and in a fully assembled condition. Replaced products
and parts shall become the property of ROLLER.
The user shall be responsible for the cost of shipping and returning the product.
A list of the ROLLER-authorized customer service stations is available on the
Internet under www.albert-roller.de. For countries which are not listed, the
product must be sent to the SERVICE-CENTER, Neue Rommelshauser Strasse 4,
71332 Waiblingen, Deutschland. The legal rights of the user, in particular the
right to make claims against the seller in case of defects as well as claims due
to wilful violation of obligations and claims under the product liability law are
not restricted by this warranty.
This warranty is subject to German law with the exclusion of the confl ict of laws
rules of German International Private Law as well as with the exclusion of the
United Nations Convention on Contracts for the International Sales of Goods
(CISG). Warrantor of this world-wide valid manufacturer’s warranty is Albert
Roller GmbH & Co KG, Neue Rommelshauser Straße 4, 71332 Waiblingen,
Deutschland.
7. Spare parts lists
For spare parts lists, see
www.albert-roller.de
→ Downloads → Parts lists.
eng eng
4. Faults
4.1. Fault:
The desired test pressure is not reached.
Cause:
Remedy:
●
Suction fi lter (6) is blocked.
●
Clean suction fi lter, change if necessary.
●
Return valve (14) does not close
●
Clean return valve and seal seat, change return valve if necessary.
●
O-ring on pump piston damaged.
●
Change O-ring.
●
Hand pressure testing pump sucks in air.
●
Check water/liquid level in the tank (3), fi ll up if necessary.
●
Installed system leaking.
●
Seal installed system.
●
Shut-off valve (F) not closed.
●
Close shut-off valve.
●
Hand pressure testing pump defective.
●
Have the hand pressure testing pump checked/repaired by an authorised
ROLLER customer service workshop.
4.2. Fault:
Test pressure is not held.
Cause:
Remedy:
●
Shut-off valve (E) and/or (F) not closed.
●
Close shut-off valve.
●
Installed system leaking.
●
Seal installed system.
●
Hand pressure testing pump defective.
●
Close shut-off valve (E). Have the hand pressure testing pump checked/
repaired by an authorised ROLLER customer service workshop.
4.3. Fault:
Pump lever (4) rises.
Cause:
Remedy:
●
Ball of the pump on pressure side does not close.
●
Clean ball and ball seat, change ball if necessary.
●
Hand pressure testing pump defective.
●
Have the hand pressure testing pump checked/repaired by an authorised
ROLLER customer service workshop.
6

Roller Control Specifications

General

Charging Time	2 hours
Compatibility	iOS, Android
Connection	Bluetooth 5.0
Color Options	Black, White, Blue
Material	Plastic and aluminum