EN User Manual – Go to www.ronstan.com . See SUPPORT section.
FR Manuel de l’utilisateur- Allez sur www.ronstan.com . Consultez la section SUPPORT
ES Manual del usuario - Ir a www.ronstan.com . Vea la sección SUPPORT
IT Manuale utente - Vai www.ronstan.com . Vedere la sezione SUPPORT
NL Gebruiksaanwijzing - gaan naar www.ronstan.com . Zie SUPPORT sectie
DE Benutzerhandbuch - Gehe zu www.ronstan.com . Siehe Abschnitt SUPPORT
USER MANUAL
CLEAR START
™
RACE TIMER & SAILING WATCHES
TYPICAL DISPLAYS
TIME
FUNCTION
STANDARD
SEQUENCE
Hours:Minutes
Day-Month/Seconds
Countdown
Minutes:Seconds
Time of Day
Hours:Minutes/Seconds
LINE 1
LINE 2
LINE 1
LINE 2
CHRONOGRAPH
FUNCTION
MATCH RACE
SEQUENCE
Hours:Minutes
Countdown
Minutes:Seconds
Time of Day
Hours:Minutes/Seconds
ALARM
FUNCTION
USER SET
SEQUENCE
Minutes:Seconds
Time of Day Hours:Minutes
/Chronograph Hours
Countdown
Minutes:Seconds
Time of Day
Hours:Minutes/Seconds
START/
STOP
MODE
ALARM ON
COUNT DOWN
COUNT UP - CHRONOGRAPH REPEAT
LIGHT ON
SOUND SIGNAL ON
DISPLAY
LINE 1
DISPLAY
LINE 2
CLEAR
SET
SYNC
BUTTONS & DIGITAL DISPLAY SYMBOLS
1. TURNING ON THE DISPLAY
The digital display is supplied “Turned Off” from the factory to
conserve battery life. To “turn on” the digital display press and hold
[CLEAR]. While holding in [CLEAR] press and hold at the same
time the [MODE], [SYNC], [START/STOP] for 5 seconds.
2. RACE TIMER MOUNTING
The Clear Start Timer can be worn on the wrist like a watch or
mounted on the mast, boom or deck. For mounting on the boat, the
wrist strap should be removed and the housing fixed to the boat
with M4 or 5/32” fasteners through the two holes provided. Care
should be taken in selecting and fitting fasteners correctly, so that
they do not protrude and prevent the Timer from snapping into the
housing fully.The Timer can be snapped into the housing for racing
and can be easily removed afterward for transport/security.
Make sure the Timer is placed fully into the housing and the
snap fit is secured completely before use.
3. BACKLIGHT & SOUND SIGNALS
When the Backlight function is switched on. In any mode, press
[SET ]. The backlight will stay on for 4 seconds.
Frequent use of the backlight will shorten battery life. To extend
the battery life, the Backlight function can be switched off.
When the Sound Signal function is switched on, in Racing mode
various sound signals will be given at pre-programed intervals and
critical points in the countdown – see section 7 for details.
To switch the Backlight and Sound Signal functions on or off.
In Time mode, hold in [SET
] for 4 seconds. The Backlight
symbol [ ] and/or Sound Signal symbol [ ] will flash. While
flashing press [SYNC] several times to scroll through the options
for light and sound functions to be on or off. When switched on
the symbol will be visible, when off the symbol will not be visible.
If both Backlight and Sound Signal functions are switched off the
symbols will not be visible. To switch back on hold in [SET ]
for 4 seconds until you hear a single beep and the symbols
will be visible.
Switching off the sound signal function will not affect the daily
(wake-up) alarm, and a sound signal will always be given when
an active button is pressed.
4. CHANGING BETWEEN TIME & RACING MODES
To change between the Time and Racing modes press at the same
time [MODE] then [SYNC].
The last function or start sequence used will be remembered
when you change modes.
5. TIME MODE
5.1. Changing Between Time Functions
When in Time mode press [MODE] several times to scroll through
the functions. Time > Chronograph > Alarm.
(continued on next page)
CONTENTS
1. Turning On The Display
2. Race Timer Mounting
3. Backlight & Sound Signals
4. Changing Between
Time Or Racing Modes
5. Time Mode
6. Racing Mode
7. Sound Signals
To Next Page
Need help?
General
