Ross Carbonite Series - Custom Controls; Custom Control Events

DescriptionLocationEvent
Select the position for the bottom edge
of the box mask on the selected key
for the selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) —
Bottom Edge
PositionMask (Box)
— Bottom Edge
Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select Bottom Edge.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Select the position for the left edge of
the box mask on the selected key for
the selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) — Left
Edge Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select Left Edge.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Select the position for the right edge
of the box mask on the selected key
for the selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) —
Right Edge
Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select Right Edge.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Select the size of the box mask on the
selected key for the selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) — Size
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
DescriptionLocationEvent
3. Click the Parameter button and
select Size.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new size in the Value
(%) field.
Select the position for the top edge of
the box mask on the selected key for
the selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) — Top
Edge Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select Top Edge.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Select the x-axis position of the box
mask on the selected key for the
selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) —
X-Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select X-Pos.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Select the y-axis position for the box
mask on the selected key for the
selected ME.
Switcher >
Keyer > Box
Mask Param
Mask (Box) —
Y-Position
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Keyer button for the
key you want to perform the
event on.
3. Click the Parameter button and
select Y-Pos.
4. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
5. Enter a new position in the
Value (%) field.
Carbonite Operation Manual (v13.0) — Custom Controls • 69