Ross Carbonite Series - Custom Controls; Custom Control Events

DescriptionLocationEvent
Select the aspect ratio for the pattern
mask for the selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Aspect Ratio
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Aspect.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter an aspect ratio in the
Value (%) field.
Select the size of border for the pattern
mask on the selected key for the
selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Border Size
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Border Size.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter a size for the border in the
Value (%) field.
Select the amount of softness to apply
to the edge of the mask for the
selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Edge Softness
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Softness.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter an amount of softness for
the pattern or border in the
Value (%) field.
Select the number of times you want
to multiply the pattern mask
horizontally for the selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Horizontal
Multiplication
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Horizontal Mult.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter the number of times the
pattern is multiplied in the Value
field.
DescriptionLocationEvent
Select a pattern for the pattern mask
for the selected ME.
Switcher >
Keyer >
Pattern Mask
Effect
Mask (Pattern) —
Pattern
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Pattern and select the
pattern you want to use for the
pattern generator.
Reset the mask for the selected ME.Switcher >
Keyer >
Mask (Pattern) —
Reset
1. Click the ME button for the ME
that you want to perform the
event on.
Pattern Mask
Reset
2. Click Reset Params.
Select the rotation for the pattern mask
for the selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Rotation
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Rotation.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter a rotation in the Value (%)
field.
Select the size of the pattern mask for
the selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Size
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Size.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter a new size in the Value
(%) field.
Select the number of times you want
to multiply the pattern mask vertically
for the selected ME.
Switcher >
Keyer >
Pattern Mask
Param
Mask (Pattern) —
Vertical
Multiplication
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Vertical Mult.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter the number of times the
pattern is multiplied in the Value
field.
70 • Custom Controls — Carbonite Operation Manual (v13.0)