Ross Carbonite Series - Custom Controls; Custom Control Events

DescriptionLocationEvent
2. Click the Box button and select
the box that you want perform
the event on.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Click a Value button and select
whether a red tally is shown on
the selected box (On) or not
(Off).
Assign a source to one of the boxes
on the selected MultiViewer.
MultiViewer >
Box > MV Box
Source
MultiViewer Box —
Video Source
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click the Box button and select
the box that you want perform
the event on.
3. Click the Value button and select
the source that you want to
assign to the box.
Select the amount of clipping to be
applied to the overlay source on the
selected MultiViewer.
MultiViewer >
MV Keyer Clip
MultiViewer — Clip
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
3. Enter the amount of clipping to
be applied in the Value field.
Select a preset color for the
background of the clock on the
selected MultiViewer.
MultiViewer >
Clock > MV
Clock (Preset
Color)
MultiViewer Clock
— Background
Color (Preset)
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click Background.
3. Click the Color button and select
the color you want to use.
Select the custom color for the lettering
of the clock on the selected
MultiViewer.
MultiViewer >
Clock > MV
Clock (HSL
Color)
MultiViewer Clock
— Foreground
Color (HSL)
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click the Clock Area button and
select Foreground.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
DescriptionLocationEvent
4. Click the Component button and
select the HSL component you
want to assign a value to. A
value should be applied to all
three components.
5. Enter a value for the selected
component in the Value (%)
field.
Select a preset color for the lettering
of the clock on the selected
MultiViewer.
MultiViewer >
Clock > MV
Clock (Preset
Color)
MultiViewer Clock
— Foreground
Color (Preset)
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click Foreground.
3. Click the Color button and select
the color you want to use.
Select the hour format for the clock on
the selected MultiViewer.
MultiViewer >
Clock > MV
Clock Format
MultiViewer Clock
— Format
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click a Value button and select
whether the clock shows 24-hour
(24-Hours), 12-hour with am/pm
(12-Hour AM/PM), or simple
12-hour (12-Hour) clock.
Select whether the clock shows
timecode or system time on the
selected MultiViewer.
MultiViewer >
Clock > MV
Clock Mode
MultiViewer Clock
— Mode
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click a Clock Mode button and
select whether the clock shows
timecode (Timecode), system
time (System), or is off (Off).
Select the size of the clock on the
selected MultiViewer.
MultiViewer >
Clock > MV
Clock Param
MultiViewer Clock
— Size
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click Clock Size.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter the size of the clock in the
Value (%) field.
Select whether number of frames for
a timecode are shown on the selected
MultiViewer.
MultiViewer >
Clock > MV
Clock Frame
Count
MultiViewer Clock
— Timecode Frame
Count
1. Click a MultiViewer button to
select which MultiViewer you
want that you want to perform
the event on.
2. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
Carbonite Operation Manual (v13.0) — Custom Controls • 77