Ross Carbonite Series - Custom Controls; Custom Control Events

DescriptionLocationEvent
Select the aspect ratio for the wipe
pattern you want to use for a wipe
transition of the selected ME.
Switcher >
Transition >
Wipe Param
Wipe Pattern —
Aspect Ratio
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Aspect.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter an aspect ratio in the
Value (%) field.
Select the custom color you want to
apply to the border of the pattern for
Switcher >
Transition >
Wipe Pattern —
Border Color (HSL)
the wipe transition of the selected ME.Wipe Border
Color (HSL) Each component of the HSL color must
be inserted individually.
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Matte button and select
Wipe Border.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Click the Component button and
select the HSL component you
want to assign a value to. A
value should be applied to all
three components.
5. Enter a value for the selected
component in the Value (%)
field.
Select the preset color you want to
apply to the border of the pattern for
the wipe transition of the selected ME.
Switcher >
Transition >
Wipe Border
Color (Preset)
Wipe Pattern —
Border Color
(Preset)
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Matte button and select
Wipe Border.
3. Click the Color button and select
the preset color you want to
apply to the border.
Select the size of border for the wipe
pattern you want to use for a wipe
transition of the selected ME.
Switcher >
Transition >
Wipe Param
Wipe Pattern —
Border Size
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Border Size.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter a size for the border in the
Value (%) field.
DescriptionLocationEvent
Select the amount of softness to apply
to the edge of the pattern or border for
Switcher >
Transition >
Wipe Param
Wipe Pattern —
Edge Softness
the wipe pattern you want to use for a
wipe transition of the selected ME.
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Softness.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter an amount of softness for
the pattern or border in the
Value (%) field.
Select the number of times you want
to multiply the wipe pattern horizontally
Switcher >
Transition >
Wipe Param
Wipe Pattern —
Horizontal
Multiplication for the wipe transition of the selected
ME.
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Horizontal Mult.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter the number of times the
pattern is multiplied in the Value
field.
Select the pattern you want to use for
a wipe transition of the selected ME.
Switcher >
Transition >
Wipe Effect
Wipe Pattern —
Pattern
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Pattern button and
select the pattern you want to
use for the wipe.
Select the rotation for the wipe pattern
you want to use for a wipe transition
of the selected ME.
Switcher >
Transition >
Wipe Param
Wipe Pattern —
Rotation
1. Click the ME button for the ME
that you want to perform the
event on.
2. Click the Parameter button and
select Rotation.
3. Click the Change Type button
and select whether you want to
set (Absolute) or reset (Reset)
the parameter. Some selections
will not be available when you
reset the parameter.
4. Enter a rotation in the Value (%)
field.
Select the size for the wipe pattern you
want to use for a wipe transition of the
selected ME.
Switcher >
Transition >
Wipe Param
Wipe Pattern —
Size
1. Click the ME button for the ME
that you want to perform the
event on.
84 • Custom Controls — Carbonite Operation Manual (v13.0)