Rovus NANO - Included Components and Parts; Main and Accessory Components; Device Part Identification; Before First Use

4 5
17. This device should never be switched on or stay plugged in power supply when not in use, while
replacing accessories or during cleaning.
18. In order to avoid a hazard due to inadvertent resetting of the thermal cut-out, this appliance
must not be supplied through an external switching device, such as a timer, or connected to a
circuit that is regularly switched on and o by the utility.
19. To avoid the risk of electric shock, do not immerse the cord, plug or appliance into water or other
liquids.
20. Regularly remove blockages caused by dust, u, hair etc. because they greatly reduce device’s
general performance.
21. Each product is 100 % quality tested to ensure product performance and safety. Thus, you may
notice some water residue in/on the device.
22. This product uses high temperature steam and thus contact with any bystanders, animals and
user‘s own body parts should be avoided.
23. During use, do not turn over the product. Do not shoot the steam to human beings or pets to avoid burns.
24. The liquid or steam must not be directed towards equipment containing electrical components,
such as the interior of ovens.
25. If the oor to be cleaned is occupied by electrical appliances or objects that cannot tolerate
steam (including, but not limited to power sockets), remove or protect the electrical appliances
or objects before cleaning.
26. The use of attachments or accessories not recommended or sold by the product distributor may
cause personal or property hazards or injuries.
27. Care should be taken when using the appliance due to the emission of steam; unplug the
appliance during lling and cleaning.
28. Regarding the instructions for lling, cleaning and descaling, please refer to the below paragraphs.
29. Although the device has been checked its usage and consequences are strictly user responsibility.
MAIN SET INCLUDES (see Picture 1)
A = Main unit (1x)
B = Cleaning nozzle / tube (1x)
C = Attachment for textile and disinfection (1x)
D = Round brush (1x)
E = Cloth (for textile steaming) (1x)
F = Cup (1x)
G = User manual (1x)
ACCESSORY SET INCLUDES (see Picture 2)
H = window cleaning attachment/squeegee (1x)
I = Cloth (for textile steaming) (2x)
J = exible hose (1x)
K = small plastic round brush (1x)
L = small metal round brush (1x)
PARTS LIST (see: Picture 3)
1. Water container lid
2. Steam switch
3. Constant steam lock
4. Handle
5. Self-cleaning button
6. Power cable
7. Power switch
8. Bottom water level window
9. Indicated light (Red/Blue)
- Red light in Steam mode
- Blue light in Self-cleaning mode.
10. Nozzle
BEFORE FIRST USE
Take out the product and the components, remove all packaging materials and check for possible damage on any of them.
NOTE: The appliance requires a short run-in time. At the start, the steam output is very irregular and damp, single droplets of water may leak out shortly.
Assembling accessories:
NOTE: Before any disassembly or maintenance make sure, the device is turned o and unplugged from power supply.
Step 1: Push the rear end of any chosen accessory onto the steam nozzle and lock it by turning it counter clockwise. (see Picture 4).
Step 2: The round brush can be slide onto any nozzle (see Picture 5).
USAGE – MAIN UNIT
Step 1: Place the device on a rm surface.
Step 2: Open the water container lid upwards.
Step 3: Use cup to ll water into the device.
NOTE: When lling the water, pay attention to the marking (MAX). Fill a maximum of 270 ml distilled water or tap water into the water container.
Step 4: Close the water container lid downwards.
Step 5: Plug the device in power supply. Press the power switch and its light turns on.
Step 6: Press and hold or lock (by sliding constant steam lock downwards) the steam switch, the light in water tank will be on (Red light). After approximately15 seconds the steam will
start to release.
Step 7: When you stop using the device, release or unlock (by sliding constant steam lock upwards) the steam switch. Press power switch to turn the device o.
NOTES:
• If the steam volume is reduced or stopped during use, water will probably have to be relled.
• When the water container is empty and all the steam emits from nozzle, the indicated light in the water tank will shut o and the heating element will stop working.
• It is suggested not to leave any unused water in the tank to avoid mold or lime scale build up.
• It is highly recommended to use only distilled water to avoid lime scale clogging of the device and/or accessories.
• Do not add any additives like perfume, vinegar, starch, dirt-cleaning gel, cleaning gel or other chemical materials to water in container.
• Store the appliance in a dry location that is protected from frost and direct sunlight.
• Allow the device to cool down and accessories to completely dry before storing them.
USAGE – ACCESSORIES
NOTES:
• Prior to using the appliance on any surface or textile, always make sure that material is not sensitive to steam by doing a test on a concealed area rst before using on a whole
product/area.
• Do not direct the steam at glued laminated edges as the edge may loosen.
• Do not use the appliance for cleaning unsealed wood or parquet oors.
• Do not use the appliance for cleaning painted or plastic coated surfaces such as kitchen or living room furniture, doors or parquet.
• To clean these surfaces, steam a cloth briey and use it to wipe over the surfaces.
• Steam can damage sealed points of the window frame and, at low outside temperatures, lead to tension on the surface of window panes and hence to glass breakages. Do not direct
the steam at sealed points on the window frame. At low outside temperatures, heat up the window panes by gently steaming the full surface of the glass. Clean the window area with
a manual nozzle and cover. To remove the water, use a squeegee or wipe the surfaces dry.
• Plastic/metal brushes can scratch sensitive surfaces. They are not suitable for cleaning sensitive surfaces.
Steam nozzle: The steam nozzle can be used for the following application areas without accessories:
1. For removing slight creases from the hanging clothing items: Steam the clothing item from a distance of 10-20 cm.
2. For wiping damp dust: Steam a cloth briey and use it to wipe over furniture.
Small plastic/metal round brushes: The round brushes are used for cleaning stubborn dirt that can be removed more easily that way.
Attachment for textile and disinfection: It can be used for cleaning small areas that can be washed down, shower cubicles and mirrors. Usually, the microber cloth / window attachment
should be used with this accessory.
CLEANING AND MAINTENANCE
NOTE: Before cleaning, please make sure the product has been turned o and unplugged from power supply. Also, make sure that the product and components/accessories have been
cooled down.
Step 1: After using the product, remaining water in the water container must be poured from the device and left to air-dry, to avoid the oxidation of the water container.
Step 2: Do not use hard or sharp objects to clean the product or other components to avoid damages.
Step 3: Take away the cloth and use mild cleaning agent to thoroughly clean the cloth. Let it air-dry thoroughly before further use or storage. Step 5: Use soft wet cloth to clean the machine
body, the nozzle and all other accessories. Then use dry soft cloth to wipe dry the product.
Step 4: Put the product and the accessories in a dry and cool place out of reach of children or animals.
Step 5: If the product is not used for a prolonged period of time, you may disassemble the product according to disassemble procedures.
NOTES:
• After the cooling of the product, hot steam will become water vapor after cooling. Some water vapor will accumulate in the mop head and become water drops drilling out, which is
a normal phenomenon – so make sure to let it dry completely
• Cleaning cloths can be machine washed on low temperatures.
• Do not put cleaning cloths into a dryer. Air-dry it.
• The cleaning cloth is a consumable item. Please replace with new cleaning cloth when appropriate in order not to aect the cleaning eect.
• If the end of the thread appears on the cleaning cloth, please cut it carefully and do not pull.
• If the product become blocked by lime scale, mix one part of citric acid with three parts water. Pour this mixture into the water container and leave it for 6 hours. After that, turn the
device ON over non-citric acid/water resistant surface.
Self-cleaning
Step 1: Switch o and unplug the device.
Step 2: Allow the appliance cool down. Drain the water completely out of the water tank.
Step 3: Mix descaling solution with water according to the details. Fill the mixed descaling solution into the water tank.
Step 4: Push the self-cleaning button to up position.
Step 5: Plug in the appliance, open power switch and long press/lock the steam switch.
Step 6: Only water pump will work in this mode and the light in the water tank will be on. (Blue light)
Step 7: Once self-cleaning function starts, the mixed descaling solution emits from steam nozzle.