Saddlemen 808-07-0042

To Next Page

IS-11-400421 (10-21)

DESCRIPTION: Dominator Solo Seats PART NUMBERS: 808-07-0042, 897-06-0042

FITMENT: Harley-Davidson® Touring models 1997-2021 897-07-0042

Congratulations on choosing a new Saddlemen® Dominator Solo seat for your

motorcycle! The Dominator's unique styling hides the mounting hardware un-

der the seat for the cleanest look possible. The included installation hardware

is also made to accept a Saddlemen passenger pillion, when you want to bring

along a passenger.

Please read these instructions completely before starting installation. All “NOTE” “CAUTION” and “WARNING” notations are serious

safety issues and should be read carefully. Possible injury to riders or damage to the motorcycle and/or accessory may result if improperly

installed.

These instructions contain important information for future reference and should be given to the customer.

Because of the variety of motorcycle conﬁgurations, other accessories, and the features and intended use of this Saddlemen seat, there may be

dierent mounting options. You are responsible for the proper installation of this seat on your motorcycle. Your attention to these installation instruc-

tions, any additional speciﬁc instructions and recommendations will permit the safe and proper use of this seat. You must mount this seat properly

and securely before riding your motorcycle. If you lack the ability to safely and properly install this seat, seek out a qualiﬁed motorcycle technician

for assistance. During installation, you may need to support the motorcycle with a suitable stand or lift so it will not tip over and injure you, or damage

the vehicle. Using or mounting this seat improperly could result in a loss of control of the motorcycle which could result in damage to your motorcy-

cle or other personal property, the property of third parties, and/or personal injury to yourself or others, up to and including death.

BE SURE TO THOROUGHLY READ AND CLOSELY FOLLOW THE MOUNTING INSTRUCTIONS THAT ARE INCLUDED WITH THIS SEAT.

• The seat must be installed and securely fastened onto the chassis of the motorcycle. Refer to your motorcycle’s Owner’s Manual and/or Service Manual for guidance.

• If you do not understand these instructions DO NOT mount the seat, and remove any seat related components you may have already installed on your motorcycle.

• Thoroughly inspect your motorcycle’s seat before every ride. Do not use this seat if its mounting system has been modiﬁed, has deteriorated, loosened or is beginning to fail.

• Continually check the security of your seat and other accessories at each stop as you ride. Items attached to your motorcycle can loosen during operation, so be sure to check them

frequently.

• Do not use this seat if you have any doubts as to whether it is properly mounted to your motorcycle. You must be sure that the installation of the seat will not damage your motorcy-

cle’s painted or plated parts. Saddlemen is not responsible if you or your technician mount the seat and it damages your motorcycle for any reason.

• When using any accessory, do not exceed your vehicle's Maximum Gross Vehicle Weight as listed on your motorcycle or in the manufacturer's owner's manual.

• If your seat is ever damaged, do not use it until it has been inspected by your local professional motorcycle dealer. You may also need to send your seat to Saddlemen for inspection

or repair. Replace any mounting part immediately if it has sustained damage that will prevent the seat from being properly secured to your motorcycle.

PASSENGER GRAB STRAP: This accessory seat is provided without a passenger grab strap. Carrying a passenger without a grab strap in place on your motorcycle may be hazardous

for the passenger. Grab straps, rear mounted foot pegs, sissy bars, passenger backrests and trunks aid in making a passenger more secure on the vehicle. Laws in some jurisdictions

require grab straps or other security devices when a passenger is transported. Do not transport a passenger if they are not secure. Do not disable grab straps or other safety features

provided on your motorcycle and obey all trac laws while riding.

Saddlemen oers a complimentary grab strap for this seat, part no. 15327. Call (310) 638-1222 for more information. Always ride responsibly and take precautions to be sure your

passenger is secure and comfortable at all times.

Need help?

Do you have a question about the Saddlemen 808-07-0042 and is the answer not in the manual?

The Saddlemen Dominator Solo Seat is an aftermarket motorcycle seat designed for Harley-Davidson® Touring models from 1997-2021. It is available under part numbers 808-07-0042, 897-06-0042, and 897-07-0042.

Function Description:

The primary function of the Dominator Solo Seat is to provide a comfortable and secure seating option for the rider. Its unique styling is designed to conceal the mounting hardware, contributing to a clean aesthetic for the motorcycle. The seat is also engineered to accommodate a Saddlemen passenger pillion (sold separately), allowing for easy conversion to carry a passenger when desired. The design aims to integrate seamlessly with the motorcycle's frame, offering both functionality and an enhanced visual appeal.

Important Technical Specifications:

Compatibility: Specifically designed for Harley-Davidson® Touring models manufactured between 1997 and 2021.
Mounting System: Features two mounting brackets on the bottom rear of the seat pan and a front slot that slides over a frame tab. It utilizes two threaded studs on the bike's rear fender for secure attachment, secured with included flange nuts.
Torque Specification: The flange nuts should be tightened to 10-15 ft/lbs, with a caution against overtightening.
Passenger Pillion Integration: Designed to accept Dominator passenger pillion seats, which feature two slotted brackets at the front that slide into the flange nuts holding the solo seat. The rear single mounting tab of the pillion can then be installed into the original seat mounting point in the rear fender.
Material and Workmanship: Saddlemen seats are made in the U.S.A. using high-quality materials.
Warranty: Comes with a one-year limited warranty against defective material and workmanship from the date of retail purchase.

Usage Features:

Clean Aesthetic: The Dominator's design hides mounting hardware for a smooth, clean look.
Passenger Pillion Ready: Easily converts to a two-up seating arrangement with the addition of a compatible Saddlemen passenger pillion.
Installation: The installation process involves locating mounting brackets and a front slot on the seat, engaging a frame tab, and securing the rear with two flange nuts onto existing threaded studs. For 2014 and later H-D Touring models, removal of two metal frame bumpers may be required.
Safety Warnings: Emphasizes the importance of proper and secure installation to prevent injury or damage. Users are advised to seek professional assistance if they lack the ability to safely install the seat.
Pre-Ride Inspection: Users are instructed to thoroughly inspect the seat's mounting system before every ride and to continually check the security of the seat and other accessories at each stop.
Paint Protection: Saddlemen recommends using an Adhesive Fender Washer (PN: 8901) and a Protective Tape Kit (PN: 4320-0807) to prevent abrasion damage to painted or finished surfaces on the motorcycle, especially in areas where the seat may touch the chassis.
Passenger Grab Strap: While the accessory seat is provided without a passenger grab strap, Saddlemen offers a complimentary grab strap (part no. 15327) and stresses the importance of passenger security, noting that laws in some jurisdictions may require grab straps or other security devices.

Maintenance Features:

Cleaning: Requires minimal maintenance, primarily periodic cleaning with mild soap and water.
UV Protection: Application of a UV inhibitor is recommended to prevent color fading caused by UVA and UVB sun exposure to the thread. Ray Bloc Fabric Protector or similar products are suggested.
Damage Inspection: Users should not use the seat if its mounting system has been modified, deteriorated, loosened, or is failing. Any damaged mounting part should be replaced immediately. If the seat itself is damaged, it should be inspected by a professional motorcycle dealer or sent to Saddlemen for inspection/repair.
Warranty Coverage: The one-year warranty covers replacement parts and labor for defects in material or workmanship. It does not cover damage from abuse, lack of maintenance, normal wear and tear, or damage to the motorcycle or personal injury. Transportation charges for warranty returns to Saddlemen are not covered, but return ground transportation for repaired products is covered.
Fitment Check: Before final mounting, users should carefully check the fitment of the new seat, placing a cloth under the seat to protect painted surfaces.
Hardware Inspection: Inspect mounting hardware before and during each ride to ensure it remains secure and does not interfere with vehicle operation.