Safeline Signature 2 User Manual

168 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

SAFELINE INC

Safeline Business Center

6005 Benjamin Road

Tampa, Florida 33634 USA

Tel: 813 889 9500 / 800 447 4439

Fax: 813 881 0840

Web Site: www.metaldetection.com

Email: sales@safeline.net

service@safeline.net

parts@safeline.net

Table of Contents

Default Chapter2
- Preliminary Pages2
- Aims of this Manual2
- Amendments3
- Handling Instructions5
- Detector Precautions7
- Table of Contents9
- Index13
List of Illustrations14
- Features of Your Metal Detector19
- Product Numbers19
- Timer Groups19
- Timer Types19
- Product Signal Cancellation (PSC) (Option)19
- Automatic Tracking (Option)19
- Inverse Detection19
Quality Assurance Support (Option)20
Technical Specification21
- Technology21
- Frequency of Operation of Coil21
- Product Throughput Speed21
- Power Input21
- Internal Battery21
- Environmental Protection21
- Switched Power Output21
- Reject Relay21
- Detect Signal22
- Q.A. Due/Overdue Output22
- Pack Sensor Requirements22
- Speed Sensor Requirements22
- Reject Confirmation Sensor Requirements22
- RS232 Serial Communications22
- Internal Counters23
- Spherical Sensitivity23
- Sensitivity Gradient23
- Timer Ranges23
General24
Mechanical Installation24
- Metal Free Zone (MFZ)24
- Construction of the Detector Installation25
- Positioning the Detector Head25
- Electrical Connections25
Electrical Installation28
- General28
- Location and Layout of the Detector Terminals28
- Removing the Power Supply Box Lid28
Introduction32
- The Touch Keys Explained33
- Changing Numeric Values35
- Universal Settings Guide37
Running Mode48
- Introduction48
- Pack Count and Reject Count49
- Time49
Operator Mode51
- Introduction51
- Product Number, Auto Setup and Name51
- Sensitivity and Phase51
Supervisor Mode53
- Introduction53
- Product Number, Auto Setup and Name53
- Sensitivity and Phase53
- Operating Frequency54
- Select Timer Group54
- Reject Count54
- Pack Count54
Engineer Mode56
- Introduction56
- Product Number, Auto Setup and Name56
- Sensitivity and Phase56
- Operating Frequency57
- Power Drive57
- Select and Update Timer58
- Inverse Detection58
- Automatic Tracking (Option)59
- Reject Count59
- Pack Count59
- Pack Sensor Setup60
- Security Setup60
- Speed Setup61
- Auto. Tracking Setup61
- Detection Buzzer61
- Reject Inhibit (Versions XT1.00 and XT1.01 Only)61
- Boost Mode62
- Language62
- Set Date and Time (Option)63
- Printer Handshake (Option)63
Automatic Setup64
- Introduction64
- Product Signal Cancellation66
- Vibration Setup70
- Introduction70
- Note70
- Sensitivity Limit70
Pack Sensor Setup72
- Introduction72
- Gating72
- Pack Sensor Fitted72
- Sensor Distance72
- Pack Sensor Calibration73
Security Setup75
- Introduction75
Speed Setup78
- Introduction78
- Speed Range78
- Automatic Tracking Maximum Rate80
Qa Inspector Mode (Option)83
- Introduction83
- Printer83
- Configuring the Performance Validation Routine84
- Line Identification84
- Printer Fitted84
- Printer Fixed/Portable84
- Test Samples85
- Shift Report Options85
- Shift Report Interval86
- Shift Report Start Time86
- Test Interval87
- Overdue Period87
- Alarm if Overdue88
- Change QA Operator Code88
Qa Operator Mode90
- Introduction90
- QA Operator Security Codes90
- Carrying out a Performance Check90
- Notes on the Test Sample90
- Select Test Material90
Viewing Mode93
- Introduction93
Reject Timers Introduction94
- Recommended Applications94
- Timer Groups A, B or C94
- Sample Size Selection94
Tm1 TIMER97
Tm2[G] TIMER - NON GATED MODE100
- Introduction100
- Tm2 Settings100
Tm2G TIMER - GATED MODE104
Tm3[G] TIMER - NON GATED MODE110
- Setting up Timer Type Tm3110
Tm3[G] TIMER - GATED MODE115
- Setting up Timer Type Tm3G in Gated Mode116
Speed Sensor for the Tm3 and Tm3[G] Timers125
- Speed Sensor Requirements125
- Speed Sensor Electrical Connections125
- Producing a Rotary Encoder Using a Proximity or Photo-Electric Sensor125
- Disc Construction126
- Determining the Required Shift Distance of the Speed Sensor126
Setting up and Connecting a Printer to the Metal Detector128
- General128
- Requirements of Your Serial Printer128
- Connection of Printer to Detector129
Sample Printed Reports130
Metal Detector Serial Communications Link134
- Introduction134
- Host Computer or Intelligent Equipment134
- Specification of the Serial Link134
- Physical Layer Specification (OSI Layer 1)134
- Data-Link Layer Specification (OSI Layer 2)134
- Valid Message Identifiers136
- Commands the Host Can Transmit144
- Commands the Metal Detector May Transmit144
- Command Identifier - 'E' Error Codes146
- Command Identifier - 'Q' QA Lists and Displays148
- QA Operator Commands148
- QA Inspector Commands148
Emulation Mode152
- Objective152
- Principal of Operation152
Crc Generation158
- Method158
- C Program159
Timing Diagrams for Serial Communications160
Magnetic Loops163
Recommendations for the Use of Inverters166
Atex Directive167
- ATEX System Label168
- ATEX Static Warning Label168
- ATEX Enclosure Warning Label168

Questions and Answers:

Need help?

Do you have a question about the Safeline Signature 2 and is the answer not in the manual?

Safeline Signature 2 Specifications

General

Brand	Safeline
Model	Signature 2
Category	Metal Detector
Language	English

Related product manuals

Safeline Signature

Safeline STANDARD SERIES