Samson 3730-5 - Page 8

208 pages

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

8 EB 8384-5 EN

Table of Contents

Default Chapter3
- Table of Contents3
1 Important Safety Instructions9
2 Article Code11
3 Design and Principle of Operation12
- Additional Equipment13
- Communication13
- Technical Data15
4 Attachment to the Control Valve - Mounting Parts and Accessories18
- Direct Attachment20
- Type 3277-5 Actuator20
- Type 3277 Actuator22
- Attachment According to IEC 60534-624
- Attachment to Type 3510 Micro-Flow Valve26
- Attachment to Rotary Actuators28
- Heavy-Duty Version30
- Reversing Amplifier for Double-Acting Actuators32
- Reversing Amplifier (1079-1118 or 1079-1119)32
- Attaching an External Position Sensor34
- Mounting the Position Sensor with Direct Attachment34
- Mounting the Position Sensor with Attachment According to IEC 60534-636
- Mounting the Position Sensor to Type 3510 Micro-Flow Valve37
- Mounting the Position Sensor to Rotary Actuators38
- Attaching Positioners with Stainless Steel Housings39
- Air Purging Function for Single-Acting Actuators39
- Required Mounting Parts and Accessories40
5 Connections44
- Pneumatic Connections44
- Signal Pressure Gauges44
- Supply Pressure44
- Signal Pressure (Output)45
- Electrical Connections45
- Establishing Communication48
6 Operator Controls and Readings50
7 Start-Up - Settings52
- Defining the Valve Closed Position52
- Setting the Volume Restriction Q53
- Adapting the Display53
- Limiting the Signal Pressure54
- Checking the Operating Range of the Positioner54
- Initialization55
- MAX - Initialization Based on Maximum Range57
- NOM - Initialization Based on Nominal Range58
- MAN - Initialization Based on a Manually Selected Range59
- Sub Substitute Calibration60
- Zero Calibration63
- Reset to Default Values64
- Start-Up Via Local Interface (SSP)64
8 Operation65
- Enabling and Selecting Parameters65
- Operating Modes65
- Automatic and Manual Modes65
- SAFE - Fail-Safe Position66
- Malfunction/Maintenance Alarm67
- Confirming Error Messages68
9 Status and Diagnostic Alarms68
- Standard EXPERT Diagnostics68
- Extended EXPERT + Diagnostics69
10 Adjusting the Limit Switch70
11 Retrofitting an Inductive Limit Switch72
12 Maintenance73
13 Servicing Explosion-Protected Devices73
14 Serial Interface (Firmware Update)73
15 Fieldbus Specification75
- Device Description (DD)75
- FOUNDATION™ Fieldbus Block Model75
- Resetting the Device76
- Status Classification and Condensed State76
16 Settings in TROVIS-VIEW Software78
- General78
- System Requirements78
- Installing TROVIS-VIEW Software79
- Starting TROVIS-VIEW and Performing Basic Settings80
- Data Transmission82
- Offline Operation (Indirect Data Transmission)83
- Online Operation (Direct Data Transmission)83
- Setting Parameters84
- Initializing the Positioner and Performing an Operational Test86
- Status Classification88
17 Appendix90
- Code List90
- Parameters109
- Resource Block109
- Analog Output Transducer Block109
- Discrete Input Transducer Blocks110
- Analog Output Function Block112
- Discrete Input Function Block DI1114
- Discrete Input Function Block DI2115
- PID Function Block116
- Other Parameters118
- Stale Counter118
- Link Objects118
- LAS Functionality118
- Parameter Lists119
18 Dimensions in MM182
19 Valve Characteristic Selection184
Text Certificates187

Other manuals for Samson 3730-5

Configuration Manual136 pages

Related product manuals

Preview: Samson 3730-2

Preview: Samson 3730-4

Preview: Samson 3730-3

Preview: Samson 3730-0

Preview: Samson 3730-3 ESD

Samson 3730-3 ESD

Preview: Samson 3730 Series

Samson 3730 Series

Preview: Samson Series 3730

Samson Series 3730

Preview: Samson TROVIS 3730-1

Samson TROVIS 3730-1

Preview: Samson TROVIS 3730-3

Samson TROVIS 3730-3

Samson TROVIS SAFE 3730 Series

Samson 373 Series

Samson TROVIS SAFE 3731-3