Samsung AN17HS - Page 7

1. Bright should be cut off .
Save after adjusting like this (Color
coordinates x=0.283 + 0.02, y=0.298 + 0.02
Brightmess, 17 inch: 42 + 1 F/L, 19 inch: 38 +
1 F/L) with R,G,B gain key.
3. Adjust the high light brightness (17 and 19
inch: 65 + 1 F/L) with BMCONT key after
tr
Notice : Don’t adjust BM of AN19MT.
(There is no function for high light zone)
Adjust BM only to color,
4-3-3 (c) MODIFY WITH ABL ADJUSTMENT
CONDITIONS
Scanning frequency: 17 inch: 68 kHz / 85 Hz
19 inch : 91 kHz / 85 Hz
Screen: Full White Pattern
Bright: Cut off
Contraster: MAX
FRONT BEZEL OPENING
BACK RASTER
WHITE WINDOW
Figure 4-9. Full White Pattern
1. Bright should be cut off .
2. Save after adjusting the brightness (17, 19 inch
: 30 F/L) with ABL key .
3. Save all colors.
Notice : Save all color only to color .
The value of color while adjusting ABL is
hardly changed.
WwW 19"
i With ABL 20 ft-L 30 ft-L
| Without ABL 40 fel Bel |
Without ABL 1 fe i
t Hig 7 i Activatccs | Pree & A es
Luminance Table (93G0K) 4-4
4-3-3 (d) WHITE BALANCE AUJUSTMENT VERIFICATION
CONDITIONS
Scanning frequency: (7 inch : 68 KHz / 85 Hz
19 inch : 91 kHz / 85 Hz
Back raster pattern
x = 0,283 + 0.02,
y = 0.298 + 0.02
Display image:
X-Y Coordinates:
4 Alignment and Adjustments
Contrast: Maximum
i. Check whether the color coordinates of the
back raster satisfy the above spec.
If they do not, return to 4-3-2 (a) and readjust
all settings.
2. Display a full white pattern.
3. Adjust the Contrast Contro] on the monitor so
that the luminance of the video is about 5 ft-L.
4. Check whether the white coordinates of the
video meet the above coordinates spec.
5. Adjust the Contrast Control again so that the
luminance of the video is about 20 ft-L.
6. Check whether the white coordinates of the
video satisfies the above spec.
If they do not, return to 4-3-2 (a) and readjust
all settings.
4-3-4 Color Adjustments for 5000K
4-3-4 (a) BACK RASTER COLOR ADJUSTMENT
CONDITIONS
Scanning frequency: 17 inch : 68 kHz / 85 Hz
19 inch : 91 kHz / 85 Hz
Display image: Back raster pattern
Brightness: MAX
Contrast: MAX
1, Select COLOR CHANNEL 2 to control the
color for 5000K.
2. Adjust the luminance of the back raster to
between 0.5 to 0.7 ft-L using the G_CUT
controls.
3. Click on the << or >> boxes next to R-CUT
and B_CUT to adjust the R-Bias to x = 0.346 +
0.02 and the B-Bias to y = 0.359 + 0.02
4-3-4 (b) GAIN (WITHOUT ABL) ADJUSTMENT
1. Bright should be cut off.
2. Save after adjusting like this (Color
coordinates y=0.3460.03, y=0.3590.03
Brightness, 17 inch: 38 +1 F/L,
(Yinch: 3541 F/L) with RGB gain kev.
Notice : The condition for adjusting is the sani es
9300K. Modify to ABL adjustment.
Raster Luminance 0.3 ~ 1 ft-L
ABL Luminance 30 + 1 ft-L
Brightness: Cut-off
ANT7HS/AN17IS/
ANISMS/AN1SIS/AN19MT
45
4 Alignment and Adjustments
4-3-3 (c} WHITE BALANCE ADJUSTMENT
CONDITIONS
Scanning
frequency:
17
inch
:
68
kFIz
/
85
Hz
19
inch
:
91
kHz
/
85
Hz
Screen: Full White Pattern
Bright: Cut off
Contraster: MAX
Tight should be vut 0}
2.
Save
after
adjusting
the
brightness
(17
inch
:
30
+1F/L,19
inch:
28+1
F/L)
with
ABL
key.
Notice : Don't save ail colors after adjusting color
save all color only to color].
The value of color coordinates while adjusting
ABL is hardly changed.
4-3-4 (d) WHITE BALANCE ADJUSTMENT VERIFICATION
Refer
to
the
procedure
for
9300K,
section
4-3-3
(a).
Without ABL
With ABL
Luminance Table {5000K} 4-5.
4-3-5 Color Adjustments for sRGB
4-3-5 (a) BACK RASTER COLOR ADJUSTMENT
CONDITIONS
Scanning
frequency:
17
inch
:
68
kHz
/
85
Hz
19 inch : 91 kHz / 85 Hz
Screen: Back raster pattern
Bright: MAX
Contraster: MAX
1.
Select
COLOR
CHANNEL
3
to
contro!
the
color
for
sRGB.
Nv
Adjust the luminance of the back raster to
between
0.5
to
0.7
ft-L
using
the
G_CUT
controls.
yo
Click
on
the
<<
or
>>
boxes
next
to
R_CUT
and
B_CUT
to
adjust
the
R-Dias
to
«
=
0.312
=
0.02
and
the
B-Bias
to
v
=
0.2
4-3-5 (b] GAIN (WITHOUT ABL) ADJUSTMENT
Bright should be cut off.
2. Save after adjusting like this (Color
coordinates x=0).313 +0.015, y=0.329 £0.015
Brightess 17 and 19 inch ; 24+ 1 F/L) with R,
G, B gain key.
Notice : The condition for adjusting is the same as
9300K.
Don’t adjust ABL to SRGB Mode
Modify with ABL.
Delete all the contents and add the contents
below.
4-3-5 (c) WHITE BALANCE ADJUSTMENT
CONDITIONS
Scanning frequency: 68 kHz / 85 Hz
Display image: Full white pattern
Brightness: Cut-off
Contrast: Maximum
1. Click on the << or >> boxes next to R.GAIN
and B_GAIN to make the video white.
(For sRGB color adjustment:
x = 0.312 + 0.02, y = 0.329 + 0.02.)
2. Select COLOR FACTORY SAVE to save the
data.
Without ABL
Luminance Table 4-6.
ANT7HS/AN17IS/
ANISMS/AN1SIS/AN1 SMT