TYPES TRAY 1
OPTIONAL
TRAY
MULTI-PURPOSE
TRAY
Plain ƔƔ Ɣ
Thick ƔƔ Ɣ
Thicker Ɣ
Extra Thick Ɣ
Thin ƔƔ Ɣ
Cotton ƔƔ Ɣ
Color ƔƔ Ɣ
Preprinted ƔƔ Ɣ
Recycled ƔƔ Ɣ
Envelope Ɣ
Transparency Ɣ
Labels Ɣ
CardStock Ɣ
Bond Ɣ
Archive Ɣ
Glossy Photo Ɣ
Media and tray_ 39
( Ɣ: Supported, Blank: Not supported)
The media types are shown in the Printing Preferences. This paper type
option allows you to set the type of paper to be loaded in the tray. This
setting appears in the list, so that you can select it. This will let you get the
best quality printout. If not, the desired print quality may not be achieved.
• Plain: 60 to 90 g/m
2
(16 to 24 lb.) Normal plain paper.
• Thick: 90 to 105 g/m
2
(24 to 28 lb.) thick paper.
• Th
icker: 106 to 120 g/m
2
(28 to 32 lb.) thicker paper.
• Th
in: 60 to 70 g/m
2
(16 to 19 lb.) thin paper.
• Cotton: 75 to 90 g/m
2
(20 to 24 lb.) cotton paper.
• Color: 75 to 90 g/m
2
(20 to 24 lb.) color-backgrounded paper.
• Prep
rinted: 75 to 90 g/m
2
(20 to 24 lb.) preprinted/letterhead paper.
• Recy
cled: 60 to 90 g/m
2
(16 to 24 lb.) recycled paper.
When you use recycled paper as a used paper, printouts might be
wrinkled.
• Envelope: 75 to 90 g/m
2
(20 to 24 lb.) envelope.
• T
ransparency : 138 to 146 g/m
2
(37 to 39 lb.) transparency paper.
• Lab
els: 120 to 150 g/m
2
(32 to 40 lb.) label.
• Extra Thick: 106 to 170 g/m
2
(28 to 46 lb.) extra thick.
• CardStoc
k: 171 to 220 g/m
2
(46 to 59 lb.) cardstock.
• Bond: 105 to 120 g/m
2
(28 to 32 lb.) bond.
• Archive: 70 to 90 g/m
2
(19 to 24 lb.) If you need to keep the print-out for
a long period time, such as archives, select this option.
• Glossy Photo: 111 to 130 g/m
2
(30 to 35lb.), 131 to 175 g/m
2
(35 to
47lb.), 176 to 220 g/m
2
(47 to 59lb.)glossy photo paper.
Envelope
Successful printing on envelopes depends upon the quality of the
envelopes.
To print an envelope, place it flap sid
e up with the stamp area bottom the
top right side.
• When selecting envelopes, consider the following factors:
- Wei
ght: The weight of the envelope paper should not exceed
90 g/m
2
otherwise, jam may occur.
- Co
nstruction: Prior to printing, envelopes should lie flat with less
than 6 mm curl, and should not contain air.
- Co
ndition: Envelopes should not be wrinkled, nicked, nor
damaged.
- Temperature: Use envelopes that are compatible with the heat and
pressure of the machine during operation.
• U
se only well-constructed envelopes with sharp-and well-creased folds.
• D
o not use stamped envelopes.
• D
o not use envelopes with clasps, snaps, windows, coated lining,
self-adhesive seals, or other synthetic materials.
• D
o not use damaged or poorly made envelopes.
• Be
sure the seam at both ends of the envelope extends all the way to
the corner of the envelope.
1 Acceptable
2 Unacceptable
• Envelopes with a peel-off adhesive strip or with more than one flap that
folds over to seal must use adhesives compatible with the machine’s
fusing temperature about 170°C(338 °F) for 0.1 second. The extra flaps
and strips might cause wrinkling, creasing, or jams, and may even
damage the fuser.
• F
or the best print quality, position margins no closer than 15 mm (0.59
inches) from the edges of the envelope.
• Avoid printing over the area where the envelope’s seams meet.
To Next Page
Loading...
