Copying_ 6
5. Press On to activate this feature.
6. Pr
ess OK.
7. Pr
ess Start on the control panel to begin copying.
Book copying
Use this feature to copy a book. If the book is too thick, lift the scanner lid
until its hinges are engaged by the stopper and then close the scanner lid. If
the book or magazine is thicker than 30 mm (1.18 inches), start copying with
the scanner lid open.
This copy feature is available only when you place originals on the scanner
glass.
1. Place the originals face down on the scanner glass and close the
scanner lid.. (See "Loading originals" on page 1.)
2. Press Copy from the main screen.
To remove shadows of a book edge, press the Image tab > Edge
Erase > Book Center and Edges Erase.
3. Press the Advanced tab > Book Copy.
4. Select th
e appropriate option.
•Off:
Disables this feature.
•Left Page: Prints left page of the book.
•Ri
ght Page: Prints right page of the book.
•Both Page: Prints both facing pages of the book.
5. Pr
ess OK.
6. Pr
ess Start on the control panel to begin copying.
Booklet copying
The machine automatically prints on one or both sides of the paper, which
are then folded to produce a booklet with all of the pages in the correct
sequence.
The machine will also reduce and correctly adjust the position of each
image to fit on the selected paper.
1. Place the originals face up in the document feeder. Or place a single
original face down on the scanner glass and close the scanner lid. (See
"Loading originals" on page 1.)
2. Pr
ess Copy from the main screen.
3. Select th
e tray in Paper Supply.
4. Pr
ess the Advanced tab > Booklet.
5. Pr
ess On to use this feature, and select detailed settings for each
option.
•1 Si
ded Original: Copies on one side of originals.
•2 Si
ded Original: Copies on both sides of originals.
6. Pr
ess OK.
7. Pr
ess Start on the control panel to begin copying.
This feature is possible only with A4, Letter, Legal, Folio, Oficio, JIS
B5, ISO B5, Executive, A5 and Statement sized paper.
Cover copying
The machine automatically adds covers to your copied set using stock taken
from a different tray. Covers must be the same size and orientation as the
main body of the job.
1. Pl
ace the originals face up in the document feeder. Or place a single
original face down on the scanner glass and close the scanner lid. (See
"Loading originals" on page 1.)
2. Pres
s Copy from the main screen.
3. Select the tray
in Paper Supply.
4. Pre
ss the Advanced tab > Covers.
Once you have set the Paper Supply option to Auto, you cannot
use this feature.
5. Press On to use this feature, and select detailed settings for each
option.
•Position: Selects whether the cover will be placed at the front, back, or
both.
•Co
ver Sheet: Selects whether the cover will be 1 sided, 2 sided, or
blank paper.
•Paper Source: Select the paper tray, where the cover sheet is loaded.
6. Pres
s OK.
7. Pres
s Start on the control panel to begin copying.
Transparency copying
When you prepare transparencies for presentations, use this feature to copy
the information.
Before you start this special copy job, set the tray's Paper Types and
Paper Size to Transparency. (See "Setting the paper size and type"
on page 7.)
1. Pla
ce the originals face up in the document feeder. Or place a single
original face down on the scanner glass. (See "Loading originals" on
page 1.)
2. L
oad the right-sized transparencies into the tray you have set.
3. Se
t the paper type to Transparency.
4. Pres
s Copy from the main screen.
5. Pre
ss the Advanced tab > Transparencies.
6. Select T
ransparencies option.
•No Separa
tor: Does not place separator sheets between
transparencies.
•Blank
Sheet: Places a blank sheet between transparencies.
•Printed S
heet: Places the same image on the divider sheets as
printed on the transparency.
7. Select
media sources, in case you selected either Blank Sheet or
Printed Sheet.
8. Press OK.
9. Press Start on the control panel to begin copying.
Erasing edges
You can copy the original without any edges or margins.
To Next Page
Loading...
