Samsung SR-S2026C - Ice Maker Test Function

10-2)
Ice-maker
Test
Function
)
5.
Test
Function
@
It
is
function
for
the
case
which
needs
forced
motion
for
the
purpose
of
cleaning
and
so
on
at
the
time
of
operation
test
and
A/S.
This
function
is
performed
when
the
test
s/w
which
is
equipped
with
the
body
of
automatic
ice-maker
itself,
is
pressed
for
more
than
1.5
sec..
1)
Test
button
does
not
go
into
test
function
during
ice-eject,
levelling
for
horizontal
position
and
water
supply.
It
operates
in
the
horizontal
state.
It
does
not
operate
at
the
state
where
ice
is
fully
filled.
Only
after
ice
full
mode
is
cancelled
and
ice-check
s/w
is
off,
test
function
operates.
2)
When
test
button
is
pressed
in
the
horizontal
state
for
more
than
1.5sec.,
ice-eject
motion
starts
immediately
regardless
of
conditions
of
ice-making
container.
Therefore,
if
test
function
operates
in
the
state
where
water
does
not
freeze
yet,
water
may
be
poured.
So,
care
should
be
taken.
After
ice-eject
motion,
1cycle
of
water
supply
is
carried
out
in
horizontal
levelling
movement.
Therefore,
the
problems
of
ice-eject
movement,
horizontal
levelling
movement,
and
water
supply
can
be
checked
by
the
test
button.
At
this
time,
when
the
test
function
operates
normally,
buzzer
sound
“Ding-Dong”
occurs
and
starts
water
supply
function.
Hence,
if
buzzer
sound
“Ding-Dong”
doesn’t
occur,
it
may
be
considered
that
there
is
some
abnormality
so
that
check
and
repair
are
indispensable.
3)When
water
supply
is
finished,
it
operates
in
normal
cycle
of
ice-making—
ice-eject— horizontal restoration— water supply in order.
<Case Where Test Function does not Work>
Remark
Turn ice-check lever On — Off.
6. Function according to F-Room Door Open
@
This
is
function
to
minimize
noise
occurrence
by
stopping
operation
basically
when door F-room opens.
1)
If
F-room
door
opens
while
ice-eject
or
horizontal
levelling
is
working,
the
function
stops
immediately
at
this
point
of
time.
When
the
door
is
closed,
function
operates
normally.
2)
In
case
water
is
being
supplied,
normal
function
is
performed
regardless
of
door
open
of F-room.
3)
Accordingly,
when
F-room
door
is
opened
to
check,
if
tray
leans
or
its
angle
deviates
from
horizontal
position,
it
is
considered
that
it
stops
during
ice-eject
or
horizontal
levelling
movement.
It
doesn’t
matter
to
judge
it
as
a
defect
if
it
is
not
in
horizontal
position
after
more
than
30sec.
passes
when
F-room
door
is
closed
to
keep
horizontal
state
after
water
supply.
In
case
it
stops
by
F-room
door
open
while
it
is
operating,
Test
function
doesn’t
work
because
it
is
actually
working.
So,
after
finishing
water
supply,
test
function
operates.