Santeg Styledrain UN/UP-X 5/4

To Next Page

Santeg Styledrain UN/UP-X 5/4”- 32 mm

Ø80

300

Ø32

Ø70

78,5

350

235

Parts list

Installationguide

Installatiegids

Guide d’installation

Montageanleitung

Disclaimer

If you install the product in a way that differs from this manual, this will void all guarantees. Before installation check that the product meets all your requirements and is

not damaged. By proceeding with installation, you accept the condition of the product.

Disclaimer

Indien u het product plaatst op een manier die afwijkt van deze handleiding, vervalt alle garantie. Controleer voor plaatsing of het product aan al uw eisen voldoet en niet

beschadigd is. Indien u overgaat tot plaatsing, aanvaardt u de staat waarin het product zich bevindt.

Clause de non-responsabilité :

Si vous installez le produit d’une manière différente de celle présentée dans ce manuel, toutes les garanties seront invalidées. Contrôlez avant le placement si le produit

répond à toutes vos exigences et n’est pas endommagé. En procédant au placement, vous acceptez l’état dans lequel se trouve le produit.

Haftungsausschluss

Wenn Sie das Produkt nicht genau nach den Angaben in dieser Montageanleitung einbauen, verfällt die Garantie. Überprüfen Sie vor dem Einbau des Produkts, ob sämtliche

Voraussetzungen erfüllt sind und das Produkt nicht beschädigt ist. Sobald Sie mit der Montage beginnen, sehen Sie, in welchem Zustand sich das Produkt bendet.

68653_INSTALL_INT_ver2019.1.3

D x 2

L x 3

(see remark below)

D x 2

Technical drawing

Mounting options

1 2

Depending on the applied waste drain plug you will need to use part G or K.

Afhankelijk van de gebruikte wastafelkrepien zult u onderdeel G of K dienen te monteren.

Selon le model du crepine, vous devrez utiliser la piece G ou K.

Nach dem modell der Abussventil müssen Sie Teil G oder K verwenden.

Need help?

Do you have a question about the Santeg Styledrain UN/UP-X 5/4 and is the answer not in the manual?

This document provides installation and maintenance instructions for the Saniteg Style drain, specifically models UN/UP-X 5/4", 32 mm. The device is a waste plug system designed for basins, ensuring proper water drainage and preventing leaks when correctly installed.

Function Description:

The Saniteg Style drain serves as a crucial component in basin plumbing, facilitating the removal of wastewater. It consists of several interconnected parts, including a waste plug, a drain body, and various seals and connectors, all designed to create a watertight seal and guide water away from the basin. The system is compatible with both Type A and Type B basin configurations, indicating its versatility across different basin designs. The installation process involves assembling these components, securing them to the basin, and connecting them to the existing plumbing system. The drain's design aims to prevent clogs and ensure a smooth flow of water, contributing to the overall hygiene and functionality of the basin.

Important Technical Specifications:

The Saniteg Style drain is specified for 5/4" (32 mm) connections, which is a standard size for basin waste systems. The technical drawing (page 1, section "Technical drawing") illustrates key dimensions:

Overall height: Approximately 350 mm from the top of the basin to the lowest point of the horizontal pipe.
Horizontal pipe length: Approximately 235 mm from the center of the vertical pipe to the end of the horizontal pipe.
Vertical pipe diameter: Ø40 mm.
Basin opening diameter: The drain is designed to fit standard basin openings, with the top flange having a diameter of approximately 70 mm and the threaded section approximately Ø40 mm.
Connection points: The system includes various threaded connections (e.g., M, H, I, K, F, G, A, B, C, D, E) for assembling the different parts and connecting to the main drainage system. These connections are designed for a secure and watertight fit.
Material: While not explicitly stated, typical drain systems are made from durable materials like brass, chrome-plated plastic, or stainless steel to resist corrosion and wear.

Usage Features:

The Saniteg Style drain is designed for straightforward installation and reliable operation.

Mounting Options: The manual illustrates two main mounting options (1 and 2 on page 1), showing how the drain integrates with the basin and the underlying plumbing. Option 1 depicts a more exposed setup, while Option 2 shows a more concealed installation.
Pre-installation Steps (Page 2, Section 1): Before full assembly, users need to identify their basin type (Type A or Type B) and gather the necessary components (H, I, K, F, G). This ensures compatibility and proper part selection.
Assembly Process (Page 4, Section 4): The assembly involves several steps:
- 5a: Connecting the horizontal pipe (A) to the vertical pipe (B) and securing it with clamps.
- 5b: Measuring and cutting the pipe to the correct length using a measuring tape.
- 6, 7, 8: Illustrating the process of cutting the pipe with a saw, filing the edges smooth, and cleaning the interior to ensure a proper fit and prevent blockages.
- 9a, 9b: Showing the connection of the drain body to the basin and the attachment of the horizontal pipe, emphasizing the correct orientation and secure fastening.
Watertightness Check (Page 5, Section 10): After installation, it is crucial to check all connections for watertightness. The manual explicitly shows "X" marks on connections that are leaking, indicating the need for adjustment or re-tightening. This step is vital to prevent water damage and ensure the system functions correctly.
Compatibility: The drain system is designed to be compatible with standard basin types, offering flexibility for various bathroom designs.

Maintenance Features:

The manual implicitly suggests several maintenance aspects through its installation and troubleshooting guidelines:

Troubleshooting (Page 3, Section 3): The troubleshooting section provides visual cues for common issues, such as leaks or improper alignment. This implies that users should regularly inspect their drain for these problems.
- The first troubleshooting image shows a proper connection (green checkmark) versus an incorrect one, likely related to the sealing ring or gasket placement.
- The second troubleshooting image highlights a potential leak point (red exclamation mark) at a connection, indicating that regular checks for drips or moisture around the connections are necessary.
- The third troubleshooting image shows a proper seal (green checkmark) at the basin opening, suggesting that the user should ensure the drain plug and its seal are correctly seated to prevent leaks.
Cleaning: While not explicitly detailed as a maintenance step, the instruction to file and clean the pipe edges during installation (page 4, sections 7 and 8) implies that keeping the drain clear of debris is important for optimal function. Regular cleaning of the visible drain components and occasional flushing with water can help prevent blockages.
Part Replacement: The modular design of the drain system means that individual components can be replaced if they become damaged or worn. The detailed diagrams of each part (e.g., K, H, I, F, G on page 2) would assist in identifying and ordering replacement parts.
Leak Prevention: The emphasis on checking for watertightness after installation (page 5, section 10) is a key maintenance practice. Users should periodically re-check these connections, especially if they notice any signs of moisture or dripping under the basin.

Disclaimer and Warranty Information:

The manual includes important disclaimers regarding installation and warranty:

Installation Responsibility: The installer is responsible for ensuring the product is suitable for the intended use and that all requirements are met. Incorrect installation voids the warranty.
Product Changes: The manufacturer reserves the right to make changes to the product without prior notice.
Warranty: The warranty covers material and manufacturing defects for a period of 8,000 characters. It does not cover damage caused by improper installation, misuse, or normal wear and tear. Customers are advised to register their product for warranty purposes.

In summary, the Saniteg Style drain is a robust and versatile waste plug system designed for basins, offering clear installation instructions and emphasizing the importance of proper assembly and regular checks to ensure long-term, leak-free operation.