*.
.
Deck A is for playback only deck B is for both playback and recording.
If a cassene is loaded, you can turn the unit on and begin play
immediately by pressing the ➤ or DECK A ONLY < button.
If a cassette is loaded into deck B only, the DECK A ONLY <button
will not function.
1
2
3
4.
5.
6.
7.
8.
Select ‘TAPE”. “TAPP appears on the display, then ‘TAPE” is
replaced by the tape mode display.
Press the cassette holder (EJECT portion) to open it.
Load the cassette(s).
/ I t I
Ww
~~
DECK A
DECK B
After loading the cassette(s), push the cassette holder (EJECT
portion) back into position. “A” or “B appears on the display.
Set the DOLBY NR button according to whether the tape has been
recorded with the Dolby NR system or not.
With Dolby NR .......................... “~ B NR” appears
Without Dolby NR ..................... “~ B NR”disappears
Select deck A or deck B by pressing the DECK
A/Bbutton if required.
(If only one cassette is loaded, deck A or deck B will be selected
automatically.)
For deck A Select the reverse mode with the REVERSE MODE
button as desired.
Press the ➤ or DECK A ONLY < button to begin playback. “›” or
“<” appears on the display.
F : For forward play
DECK A ONLY+: For reverse play (Deck A only)
El
3“
[;~fl j:;
Press the ■ button to stop playback at any time.
When the end of the tape has been reached, automatic stop or reverse
will be activated.
Types of usable tapes
The type of tape used is automatically identified by the system since decks
A and B both employ an auto tape selection system. The following types
of tape can be used with this system.
Normal
cro2
Metal (Only for playback)
Note:
- Cr02/Metal tapes without sensing holes cannot be used since they
cannot be identified by the auto tape selector.
Endless tapes cannot be used.
Do not use C-120 tapes. They may jam in the mechanism.
Aut~ reverse (Deck A only)
Press the REVERSE MODE button to select the reverse mode as desired.
—.
-.
For listening to one side of the tape only.
z):
For listening to both sides of the tape in succession.
If playback has been started from the reverse side, only the
reverse side will be played back.
(~> :
iFor listening repeatedly to both sides of the tape.
Fast forward and rewind
Press the ➤ - or<< button. “›” or”<” blinks.
Where the tape has been wound to the end, the deck stops automatically.
Tape counter
Each deck has a counter. The counter of the selected deck appears on the
disp$ayand helps you to quickly locate the recorded selection for playback.
I ‘ l-l l—l
Ii-l
\ I Id l_l
I Lf
Both sides of the counter indicate tape movement with rotating graphic
disp~ys.
To reset the tape counter to “000”
In the stop mode, press the DECK A/B button to select the counter to be
rest%, then press the _ button.
- When the tape is automatically rewound during CDcomputerrecording
or tape computer dubbing, the counter automatically resets to “000”.
Relkiy playback
1. Load the cassettes into both decks.
2. Set the REVERSE MODE button to Z>.
3. Select deck A or deck B by pressing the DECK MB button if required.
4. Press the F or DECK A ONLY< button.
DECK A (forward side — reverse side) — DECK B.
DECK A reverse side — DECK B.
DECK B —
DECK A (forward side — reverse side).
Do6by NR system
Dolby Noise Reduction circuitv provides superior recording and playback
results by suppressing tape hiss by up to 10 dB.
Dolby noise reduction manufactured under license from Dolby Laboratories
Licensing Corporation.
“DOLt3Y”andthe double-D symbol Rnare trademarks of Dolby Laboratories
Licensing Corporation.
11
b
To Next Page
Loading...
