TiMER OPE~e remotecontrol)
. ....
~
..
Using the onloff timer
Set the on and off times, function to be used and volume level. Operation
will start with the selected function at the on time. The sound will be
gradually increased from a no-sound level to the volume setting (fade-in).
The power will be switched off at the off time.
The ordoff timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the Ctock is set to the correct time before setting
the timer.
Select the function for timer operation and prepare the sources to be
used.
If the function selected is tuner, tune into the desired band and
station.
For tape playback If cassettes have been loaded into both decks,
deck A takes precedence-Tape playback will start only from the
fonvard side.
- Adjust the volume level as desired.
Operation
1.
2.
3.
4.
5.
6.
7.
Press the TIMER button.
ma
;C
For AU: The clock is 12-hour
e
r--r-in
r--l-! u
display. Example: AM 1200
~
The previous timer on time setting appears.
Press the ADJUST button within 10 seconds.
Set the timer on time by pressing the+ or – TIME SET button, then
press the ADJUST button (as described under “ADJUSTING THE
CLOCK”).
,,/
,,,
‘@
c!
.-
The timer off time setting appears.
Set the timer off time as described in step 3.
The previous timer mode setting (play ”@”orrecording” @ REC”) and
the current function appear.
Select the timer mode by pressing the+ or - TIME SET button.
Each time the button is pressed, “ @ REC and “ @ “ blinks
alternately. Select” @ REC” for unattended recording.
If you wish to change the function, press the FUNCTION button
on the front panel to select the desired function.
Press the ADJUST button.
The original display returns, then the timer operation standby mode is
activated. “ @” (or”@ REC”) remains lit.
Press the A /ON button to switch off the power.
For AU: Use the POWER button instead of the&ION button.
“o” (or” @ REC) blinks during a timer controlled operation
To switch off the power during a timer controlled operation?, press the
~ ION button, The timer will be set in the standby mode.
To cfnemk the timer setthgs
Press the TIMER button repeatedly. The timer settings are displayed in
the follmwing order:
CM time
0$3 time
T%mer modeJFunction
CMginal display returns
TooMange the settings, press the TIMER button to select the setting to be
changed, then press the ADJUST button so that the display blinks.
Chamge the setting as explained above.
To re%easethe timer
After timing the power on, press the TIMER button, then press the SET/
CLEAR.
To amt the timer again with the same settings
1. Press the TIMER button, then press the SET/CLEAR.
2. Press the&ION button to switch off the power.
Notec
I%the SET/CLEAR button is pressed while the timer is being set, the
cmiginal display returns.
- The timer mode is released if a power failure occurs during timer
controlled operation.
- _The timer may not operate if a power failure occurs during timer
operation standby mode.
Ustig the sleep timer
The deep timer automatically switches off the power after a preset time
has reiapsed. The volume will gradually be reduced (fade-out) during the
I-miknrte period before the unit turns off. There are 12 time periods
availkrble:
120,110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Pre+as the SLEEP button repeatedly to select the desired sleep time.
\l/
SLEEP QC
\l/
e’
~
3Z
“SLEEP” and the selected time blink on the display. After several seconds,
the wiginal display returns. “SLEEF blinks.
Tcr dteck the remaining sleep time
Press the SLEEP button. The remaining time is displayed. After several
seczmds, the original display returns.
To walease the sleep timer while in operation
Press the SLEEP button, then press the SET/CLEAR. The timer is also
refke.ased if the power is switched off.
16
,)
To Next Page
Loading...
