BEFORE RECORDING AND DUBBING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copyright
material, permission from the copyright owner is necessary. SANYO
does not approve of, and cannot be held responsible for, any
unlawful use of this machine.
Use deck B for recording.
1. Press the cassette holder (EJECT portion) to open it and load the
cassette for recording.
2. Set the DOLBY NR button to ON or OFF as desired.
Dolby NR ON ............ “no B NW appears
Dolby NR OFF ...........” no B NW disappears
Automatic record muting
Undesirable parts of a programme can be omitted while recording.
Press the REC MUTE button on the remote control once while recording.
“REC blinks on the display and a 5-second unrecorded blank space is
created, then the cassette deck enters the record pause mode. “REC
remains lit and” ➤ ” blinks on the display.
To add another 5-second blank space, press the REC MUTE button
again.
To resume recording, press the FWD PLAY button.
Note:
The record muting function does not operate during CD computer recording
or tape computer dubbing.
Accidental erasure prevention tabs (for protecting
valuable recordings)
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement (Fig. 11).
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
RECORDING
RECORDING COMPACT DISCS
Computer recording
With computer recording, you can record a CD onto a cassette by pressing
just one button.
1.
2.
3.
4.
5.
6.
7.
Load the disc(s) to be recorded.
Load a blank cassette into deck B.
Select “CD function.
For programmed recording from up to 3 discs, programme the
material in advance (as described under’’PROGRAMMED PLAY”).
Press the disc select button (DISC 1, DISC 2 or DISC 3) to select the
disc to be recorded first, then press the STOP button (CD section).
For programmed recording, this step is unnecessary.
Press the “HIGH” or “NOR” COMPUTER REC button. “HIGH or
“NORMAL” appears briefly on the display.
HIGH: For high speed recording.
NOR: For normal speed recording.
The system automatically performs the following functions:
Deck B:
The tape rewinds to the beginning.
Recording starts.
CD player:
The player searches for the first track to be recorded, then enters
the pause mode.
CD play starts.
Manual edit recording
Recording starts without rewinding the tape initially.
Press the EDIT button to turn the “MANUAL” indication on
before proceeding to step 5.
To cancel this mode, press the button again. “MANUAL”
disappears.
After loading the cassette, the tape must be wound to the
point where you would like to starl recording.
“COMPU. REC, “REC,
“ ➤ “ and ‘r D “ appear on the display as
recording begins.
l—l n
! 1<. l_l I
TR
Em!mm
mm
1)
El
1234
;g$
5678
9 10 11 12
&
~ 13141516
After deck B stops automatically, turn over the cassette and reinsert
it.
If the tape ends while a track is still playing, the CD player enters
the pause mode at the beginning of the track that was playing.
This track will be recorded at the beginning of side B.
Press the button that was pressed instep 5. Recording of side B starts
automatically.
When the end of the tape (side B) is reached, the CD player and deck
B stop automatically.
If the last track on the CD plays completely before the end of the
tape, disc play stops automatically. Deck B also stops.
Note:
Recording starts automatically after4 seconds for high speed recording
or 8 seconds for normal speed recording, so the recording will not be
interrupted by the leader tape at the beginning of sides A and B.
A 5-second blank space is automatically recorded at the end of each
track.
To stop computer recording at any time, press the STOP button on the
CD player or deck. The CD player and deck B will stop.
When CD computer recording is used, repeat play mode is cancelled
automatically.
When high speed CD computer recording is used, Dolby NR recording
mode is cancelled automatically.
During high speed recording, normal monitoring is not possible.
When a CD of inferior quality is recorded into a tape with high speed
recording and reproduced, it may accompany some noise. In this
case, use normal speed recording.
14
To Next Page
Loading...
