TIMER OPERATION
Using the on/off timer
Set the on and off times, function to be used and volume level. Operation
will start with the selected function at the on time. The sound will be
gradually increased from a no-sound level to the volume setting (fade-in).
The power will be switched off at the off time.
The on/off timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before setting
the timer.
Select the function for timer operation and prepare the sources to be
used.
If the function selected is tuner, tune in to the desired band and
station.
For tape playback: If cassettes have been loaded into both decks,
deck A takes precedence. Tape playback will start only from the
forward side.
Adjust the volume level as desired.
Operation
1.
2.
3.
4.
5.
1
6.
7.
Press the TIMER button.
o
ON
The previous timer on time setting appears.
Press the MEMORY button within 10 seconds.
- The MEMORY button on the remote control cannot be used.
,1,
,1/
@)
/Y’\
Set the timeron time by turning the MULTI JOG control, then press the
MEMORY button (as described under “ADJUSTING THE CLOCK).
,1/
0
,1/
0
/T’\
y~
The timer off time setting appears.
Set the timer off time as described in step 3.
,1,
0
,Gf:
,1/
Q
The previous timer mode setting (play: “O” or recording: “ @ REC)
and the current function appear.
Select the timer mode by turning the MULTI JOG control.
“ @ REC and “ @ “ blink alternately. Select “ @ REC for
unattended recording.
If you wish to change the function, press the function button to be
changed.
Press the MEMORY button.
The original display returns, then the timer operation standby mode is
activated. “ ~ n (or” ~ REC) remains lit.
Press the WON button to switch off the power.
“@” (or” @ REC) blinks during a timer controlled operation.
To switch off the power during a timer controlled operation, press the
WON button. The timer will be set in the standby mode.
To check the timer settings
Press the TIMER button repeatedly. The timer settings are displayed in
the following order
On time — Off time — Timer mode/Function — Original display
returns
To change the settings, press the TIMER button to select the setting to be
changed, then press the MEMORY button so that the display blinks
Change the setting as explained above.
To release the timer
After turning the power on, press the TIMER button, then press the STOP
button (CD section) on the front panel.
To set the timer again with the same settings
1. Press the TIMER button, then press the STOP button (CD section) on
the front panel.
2. Press the c!YON button to switch off the power.
Note:
If the STOP button (CD section) on the front panel is pressed while the
timer is being set, the original display returns.
The timer mode is released if a power failure occurs during timer
controlled operation.
The timer may not operate if a power failure occurs during timer
operation standby mode.
Using the sleep timer
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button on the remote control repeatedly to select the
desired sleep time.
“SLEEP and the selected time blink on the display. After several seconds,
the original display returns. “SLEEP blinks.
To check the remaining sleep time
Press the SLEEP button once. The remaining time is displayed. After
several seconds, the original display returns.
To release the sleep timer while in operation
Press the SLEEP button, then press the STOP button (CD section) on the
front panel. The timer is also released if the power is switched off.
MAINTENANCE
Cleaning the decks A and B heads (Fig. 12)
To ensure playback and recording with good-quality sound, use cotton
swab to clean the heads, pinch rollers and capstans of the decks after
about every 10 hours of use.
If the dirl persists, soak the swab in a little methylated spirit or head
cleaning fluid and then clean.
Main unit
Use a soft cloth to remove dirt on the main unit.
If the dirt persists, dip a soft cloth into a diluted solution of neutral
detergent, wring it out, wipe away the dirt, and then take up any moisture
with a dry cloth.
Do not use benzene, thinners or alcohol since they will mar the finish of the
surfaces.
16
To Next Page
Loading...
