Sanyo PDG-DWL2500 - Computer Input; Input Source Selection (Computer 1: RGB)

-30-
Adjustments
Group/
Item
Item Name Function Initial Range Note
1 Loop Count Maximum Execution Times (OFFSET->GAIN) 10 1 - 30
2 Auto Status
Result of Auto-Calibration (Last Memory)
0: OK, 1: Adjusting, 2: Error
0 0 / 1 / 9
3 AutoWait Wait Value for each setting - 1 - 20
4 CHECK -Tolelance Torelance of OFFSET 16 1 - 255
5 Time out Wait Wait Time until Time out 20 1 - 255
Group 261 Auto Calibration (RGB)
0 OFFSET AREA H START Black Level Acquiring Area H-Start Position 975 0 - 1000
1 OFFSET AREA V START Black Level Acquiring Area V-Start Position 500 0 - 1000
2 GAIN AREA H START White Level Acquiring Area H-Start Position 25 0 - 1000
3 GAIN AREA V START White Level Acquiring Area V-Start Position 500 0 - 1000
4 Image AREA H WIDTH Black/White Level Acquiring Area 13 0 - 4095
5 Image AREA V HIGHT Black/White Level Acquiring Area Height 9 0 - 4095
6 OFFSET target Target Value of Black Level Adj. 0 0 - 1023
7 OFFSET torelance Torelance of Black Level Adj. 8 1 - 1023
8 GAIN target Target Value of White Level Adj. 940 0 - 1023
9 GAIN torelance Torelance of White Level Adj. 2 1 - 1023
10 Image Level Tolerance Tolerance of Image Level Adj. 4 1 - 255
Group 262 Auto Calibration (CVBS/SVIDEO/YCbCr 480i)
0 Y Image Area Start X Y Acquiring Area H-Start Position 0 - 1000
1 Y Image Area Start Y Y Acquiring Area V-Start Position 0 - 1000
6 Image Area H Width Image Level Acquiring Area 0 - 4095
7 Image Area V Hight Image Level Acquiring Area Height 0 - 4095
8 Y Target Level Target Value of Y Level Adj. 0 - 1023
11 Gain Tolerance Torelance of Level Adj. 1 - 255
12 Image Level Tolerance Tolerance of Image Level Adj. 1 - 255
Group 264 Auto Calibration (YCbCr)
0 Y-OFFSET AREA H START Y - Offset Acquiring Area H-Start Position 925 0 - 1000
1 Y-OFFSET AREA V START Y - Offset Acquiring Area V-Start Position 500 0 - 1000
2 CB - OFFSET AREA H START CB - Offset Acquiring Area H-Start Position 925 0 - 1000 If not used: use Y's value
3 CB - OFFSET AREA V START CB - Offset Acquiring Area V-Start Position 500 0 - 1000 If not used: use Y's value
4 CR - OFFSET AREA H START CR - Offset Acquiring Area H-Start Position 925 0 - 1000 If not used: use Y's value
5 CR - OFFSET AREA V START CR - Offset Acquiring Area V-Start Position 500 0 - 1000 If not used: use Y's value
6 Y - GAIN AREA H START Y-Gain 50 0 - 1000
7 Y - GAIN AREA V START Y-Gain 500 0 - 1000
8 CB - GAIN AREA H START CB-Gain 800 0 - 1000
9 CB - GAIN AREA V START CB-Gain 500 0 - 1000
10 CR - GAIN AREA H START CR-Gain 700 0 - 1000
11 CR - GAIN AREA V START CR-Gain 500 0 - 1000
12 Image AREA H WIDTH YCBCR Level Acquiring Area 13 0 - 4095
13 Image AREA V HIGHT YCBCR Level Acquiring Area Height 9 0 - 4095
14 Y - OFFSET TARTGET 1 0 - 1023
15 CB OFFSET TARGET 512 0 - 1023
16 CR OFFSET TARGET 512 0 - 1023
17 Y - GAIN TARGET 808 0 - 1023
18 CB - GAIN TARGET 892 0 - 1023
19 CR - GAIN TARGET 892 0 - 1023
20 OFFSET torelance Torelance of OFFSET Adj. 4 1 - 255
21 GAIN torelance Torelance of GAIN Adj. 4 1 - 255
22 Image Level Tolerance Tolerance of Image Level Adj. 4 1 - 255
Group 500 SCART (480i)
2 H Back Porch 119 0 ~ 4095
3 V Back Porch 19 0 ~ 4095
7 Overscan 52 0 - 255
8 VSBEG 4 0 - 255
16 Field Diff Even/Odd Phase Compensation 1 0 - 2
Group 501 SCART (525i)
2 H Back Porch 128 0 ~ 4095
3 V Back Porch 24 0 ~ 4095
7 Overscan 66 0 - 255
8 VSBEG 8 0 - 255
16 Field Diff Even/Odd Phase Compensation 1 0 - 2
Group 510 RGB Video (480i)
2 H Back Porch 116 0 ~ 4095
3 V Back Porch 19 0 ~ 4095
7 Overscan 52 0 - 255