Sanyo PLC-XF46N - Page 91

Electrical Adjustments
–3R_SUB_GAIN 0 ~ 255 128 –
–4G_SUB_BRT 0 ~ 8191 4096 –
–5B_SUB_BRT 0 ~ 8191 4096 –
–6R_SUB_BRT 0 ~ 8191 4096 –
–7G_GAM_BRT 0 ~ 8191 4096 –
–8B_GAM_BRT 0 ~ 8191 4096 –
–9R_GAM_BRT 0 ~ 8191 4096 –
–10G_BRT_CTRL 0 ~ 255 0 –
–11B_BRT_CTRL 0 ~ 255 0 –
–12R_BRT_CTRL 0 ~ 255 0 –
S 920 – PC/AV COMMON ADJ.
–0G_SIG_CNTR 0 ~ 255 33 –
–1B_SIG_CNTR 0 ~ 255 33 –
–2R_SIG_CNTR 0 ~ 255 33 –
–3G_GAIN_CTRL 0 ~ 255 160 –
–4R_GAIN_CTRL 0 ~ 255 160 –
–5B_GAIN_CTRL 0 ~ 255 160 –
–6G_VCOM_CTRL 0 ~ 255 100 –
–7R_VCOM_CTRL 0 ~ 255 100 –
–8B_VCOM_CTRL 0 ~ 255 100 –
–9G_PSIGA 0 ~ 255 21 –
–10R_PSIGA 0 ~ 255 21 –
–11B_PSIGA 0 ~ 255 21 –
–12G_PSIGB 0 ~ 255 212 –
–13R_PSIGB 0 ~ 255 212 –
–14B_PSIGB 0 ~ 255 212 –
S 930 – Lamp Mode Change
–0ALL Lamp Mode Data 0 is displayed, set data 10 and selection is activated. 0 ~ 10 0 –
Data 11 is displayed when selection is accomplished.
Data 99 is displayed while cooling and selection is disabled,
wait until it is changed to data 0.
–12 Lamp Mode 1–4 or 1 0 ~ 10 0 –
–22 Lamp Mode 2–3 or 2 0 ~ 10 0 –
S 940 – Lamp Factory Time ( Factory use only )
–0ALL to 2L–1 Lamp Mode Changing Time for Factory ( Step:10 ) 50 ~ 200 120 –
–12L–1 to 2L–2 Lamp Mode Changing Time for Factory ( Step:10 ) 50 ~ 200 180 –
–22L–2 to ALL Lamp Mode Changing Time for Factory ( Step:10 ) 50 ~ 200 180 –
–3ALL to 2L–2 Lamp Mode Changing Time for Factory ( Step:10 ) 50 ~ 200 120 –
–42L–2 to 2L–1 Lamp Mode Changing Time for Factory ( Step:10 ) 50 ~ 200 180 –
–52L–1 to ALL Lamp Mode Changing Time for Factory ( Step:10 ) 50 ~ 200 180 –
S 941 – Lamp Factory Time ( Factory use only )
–0Unused –––
–12L–1 to 2L–2 2L-1 to 2L-2 Stopping Time for Fan D2/D3 0 ~ 180 65 –
–22L–2 to ALL 2L–2 to ALL Stopping Time for Fan D1/D4 0 ~ 180 65 –
–3Unused –––
–42L–2 to 2L–1 2L–2 to 2L–1 Stopping Time for Fan D1/D4 0 ~ 180 65 –
–52L–1 to ALL 2L–1 to ALL Stopping Time for Fan D2/D3 0 ~ 180 65 –
S 950 – SWFPGA IP DLY
–0IP Signal Delay IP Signal Delay ( 0 : ON, 1 : OFF ) 0 / 1 0 –
S 970 - GHOST
-0SHP 1 ~ 63 30 –
-1GC_ON 0 ~ 1 1 –
-2R_GC_ATT 1 ~ 255 0 –
-3G_GC_ATT 1 ~ 255 0 –
-4B_GC_ATT 1 ~ 255 0 –
-5DFT_ON 0 ~ 1 0 –
-6R_HPC_DAT 0 ~ 2047 0 –
-7R_HPC_DAT 1 ~ 2047 0 –
-8R_HPC_DAT 2 ~ 2047 0 –
-9DCK_CDAT Read only – – –
S 971 - GHOST DRIFT
-0DCK1F R Panel 0 ~ 47 1 –
-1DCK2F R Panel 0 ~ 47 1 –
-2DCK3F G Panel 0 ~ 47 1 –
-3DCK4F G Panel 0 ~ 47 1 –
-4DCK5F B Panel 0 ~ 47 1 –
-5DCK6F B Panel 0 ~ 47 1 –
S 972 - GHOST DRIFT TIMER
-0R_PANEL Ghost Timer Read only 0 ~ 32767 – –
-1R_PANEL Ghost Timer Reset Reset to set data to "10" (✽) R_panel ghost timer reset 0 ~ 10 0 –
-2G_PANEL Ghost Timer Read only 0 ~ 32767 – –
-3G_PANEL Ghost Timer Reset Reset to set data to "10" (
✽) G_panel ghost timer reset 1 ~ 10 0 –
–91–
Group
No.
Data
Range
Initial Value
Function
Item
No.
Item