Sanyo PLC-XF47 - Page 139

- 139 -
Electrical Adjustments
Pin No. Name Function Name Function Polarity I/O
220 RESETP RESETP Power ON Reset Demand "L" : Power ON reset I
221 CA unused Hardware Stand-BY Demand I
222 MD3 MD3 Bus Widht setting for Area 0 "L" : Always I
223 MD4 MD4 Bus Widht setting for Area 0 "H" : Always I
224 Scan_testen 3.3V Test Terminal I
225 AVcc_USB 3.3V USB Analog Power
226 USB1_P (analog) USB1P [Func] USB1 Data Output (+) IO
227 USB1_M (analog) USB1M [Func] USB1 Data Output (-) IO
228 AVss_USB GND
229 USB2_P (analog) unused USB2 Data Output (+) IO
230 USB2_M (analog) unused USB2 Data Output (-) IO
231 AVcc_USB 3.3V USB Analog Power
232 AVss GND
233 AN[2] / PTL[2] PRESS_SENS Pressure Sensor Input AI
234 AN[3] / PTL[3] TEMP_SENS Temperature Sensor Input AI
235 AN[4] / PTL[4] KEY1 KEY AD Converter Input AI
236 AN[5] / PTL[5] KEY2 KEY AD Converter Input AI
237 AVcc 3.3V
238 AN[6] / PTL[6] / DA[1] KEY3 KEY AD Converter Input AI
239 AN[7] / PTL[7] / DA[0] OPT1 Option Resister AI
240 AVss GND
● IIC Bus DA Converter (IC7801 M62393FP)
Pin No. Name Function Name Function Polarity I/O
11 A1 DACFANCONT1 0 ~ 255 = 13.8~ 6.0 V O
12 A2 DACFANCONT2 0 ~ 255 = 13.8~ 6.0 V O
13 A3 DACFANCONT3 0 ~ 255 = 13.8~ 6.0 V O
14 A4 DACFANCONT4 0 ~ 255 = 13.8~ 6.0 V O
4 A5 DACFANSW1 ON : 255 / OFF 0 O
5 A6 DACFANSW2 ON : 255 / OFF 0 O
6 A7 DACFANSW3 ON : 255 / OFF 0 O
7 A5 DACFANSW4 ON : 255 / OFF 0 O
● Parallel Bus I/O Expander (IC5861 FPGA_NIOS EP2C5F256C)
Pin No. Name Function Name Function Polarity I/O
L7 LENSE_OUT [7] ZOOM + Zoom UP "L" : Stop / "H" : Move O
L8 LENSE_OUT [6] ZOOM - Zoom Down "L" : Stop / "H" : Move O
L9 LENSE_OUT [5] FOCUS + Focus UP "L" : Stop / "H" : Move O
N8 LENSE_OUT [4] FOCUS - Focus Down "L" : Stop / "H" : Move O
N9 LENSE_OUT [3] LENS UP Lens Shift Up "L" : Stop / "H" : Move O
R8 LENSE_OUT [2] LENS DOWN Lens Shift UDown "L" : Stop / "H" : Move O
T8 LENSE_OUT [1] LENS L Lens Shift Left "L" : Stop / "H" : Move O
T7 LENSE_OUT [0] LENS R Lens Shift Right "L" : Stop / "H" : Move O
R9 LENSE_DET [5] LENS TOP Lens Shift Upper Limit Detect "L" : Lens Bottom Arrival I
T9 LENSE_DET [4] LENS BTM Lens Shift Lower Limit Detect "L" : Lens Top Arrival I
T10 LENSE_DET [3] LENS LE Lens Shift Left Limit Detect "L" : Lens Right Arrival I
R10 LENSE_DET [2] LENS RE Lens Shift Right Limit Detect "L" : Lens Left Arrival I
N10 LENSE_DET [1] LENS VC Lens Shift U/D Center Limit Detect I
L10 LENSE_DET [0] LENS VC Lens Shift R/L Center Limit Detect I
T6 LAMP_RX [3] LAMP4_ERR Lamp4 OFF Detect "H" : ON / "L" : OFF I
T5 LAMP_RX [2] LAMP3_ERR Lamp3 OFF Detect "H" : ON / "L" : OFF I
T4 LAMP_RX [1] LAMP2_ERR Lamp2 OFF Detect "H" : ON / "L" : OFF I
T3 LAMP_RX [0] LAMP1_ERR Lamp1 OFF Detect "H" : ON / "L" : OFF I
R7 LAMP_TX [3] LAMP4_TX_EX Lamp4 Data SEnd O
R5 LAMP_TX [2] LAMP3_TX_EX Lamp3 Data SEnd O
R4 LAMP_TX [1] LAMP2_TX_EX Lamp2 Data SEnd O
R3 LAMP_TX [0] LAMP1_TX_EX Lamp1 Data SEnd O