Sanyo PLV-Z800 - Page 66

- 66 -
No. Adjustment Item Initial Value Range Input source / Description
128 Shutdown Time C 10 0 - 30
129 Shutdown Time B-A 20 0 - 30
130
Shutdown Time C-A 20 0 - 30
131
Control Curve Change Time 1 0 - 10
132
Lamp Monitor SW 0 0 - 1 0 : Off 1 : On
133
Lamp Voltage - - - 30 - 90 Read only
134
Lamp Vol Threshold 60 50 - 90
135
Fan Speed Gain 300 0 - 1500
136
Lamp Keep Time 90 0 - 255
137
Temp Test Mode 0 0 - 12
138
Fan Cooling Vol Up 0 0 - 145
139
Fan Min. Keep Time 5 0 - 15
Group :260 AUTO CALIBRATION
0 Execute Calibration 0 0 - 1
Auto calibration will execute when the value changes. (For PC white
100% Adjustment.)
1 Loop Count 8 1 - 30 Maximum times of calibration
2 Auto Status 0 0 / 1 / 9
Read only Auto calibration result
0: End correctly 1 : On Adjustment 9 : End at Error
3 AutoWait 3 1 - 20 Wait value
4 CHECK - Tolerance 4 1 - 255 Offset Final check Tolerance
5 Time out wait 20 1 - 255 Wait time (sec)
Group:261 AUTO CALIBRATION (RGB)
0 OFFSET AREA H START 975 0 - 1000 Black Level H
1 OFFSET AREA V START 500 0 - 1000 Black Level V
2 OFFSET AREA V START 25 0 - 1000 White Level H
3 GAIN AREA V START 500 0 - 1000 White Level V
4 Image AREA H WIDTH 13 0 - 4095 White / Black Level Width
5 Image AREA V HIGHT 9 0 - 4095 White / Black Level Hight
6 OFFSET Target 20 0 - 1023 Black Level Adjustment Target Value
7 OFFSET Tolerance 1 1 - 1023 Black Level Adjustment Tolerance
8 Gain Target 955 0 - 1023 White Level Adjustment Target Value
9 GAIN Tolerance 1 1 - 1023 White Level Adjustment Tolerance
10 Image Level Tolerance 2 1 - 255 Image Level Tolerance
Group:262 AUTO CALIBRATION (CVBS / S-VIDEO)
0 Y Image Area Start X 20 0 - 1000
1 Y Image Area Start Y 200 0 - 1000
6 Image Area H Width 8 0 - 4095
7 Image Area V Hight 8 0 - 4095
8 Y Target Level 875 0 - 1023
11 Gain Tolerance 1 1 - 255
12 Image Level Tolerance 2 1 - 255
Group:264 AUTO CALIBRATION (YCbCr)
0 Y-OFFSET AREA H START 925 0 - 1000
1 Y-OFFSET AREA V STAR 500 0 - 1000
2 CB - OFFSET AREA H START 925 0 - 1000
3 CB - OFFSET AREA V START 500 0 - 1000
4 CR - OFFSET AREA H START 925 0 - 1000
5 CR - OFFSET AREA V START 500 0 - 1000
6 Y - GAIN AREA H START 50 0 - 1000
7 Y - GAIN AREA V START 500 0 - 1000
8 CB - GAIN AREA H START 800 0 - 1000
9 CB - GAIN AREA V START 500 0 - 1000
10 CR - GAIN AREA H START 700 0 - 1000