Sanyo SPW-CR703GDCH8 - Page 135

Control of W-ECO MULTI SYSTEM
3
TD831077
III - 77
2. Optional Controller (AMY adapter)
7 Connection to the outside equipments
(1) Signal input for turn-off the all units.
(Potential free normal open contact)
<Inputting photo coupler>
¶ Do not apply voltage to D1 input terminal. Take care
not to share one of the input terminals with other
input. Since the D1 input terminal is used for potential
free contact.
(2) Inputting by pulse counter
(Potential free normal open contact)
<Inputting photo coupler>
¶ AMY adapter counts the number of pulses which the
outer contact turns on through the input terminal P1,
P2 and P3. Since the contact is potential free, do not
apply voltage. AMY adapter will be damaged.
Please take care that input terminal can not be
connected with other input.
¶ Control wires used for inputting signals are field
supply. Maximum wiring length is 100 m.
Use 2-core shielded wires 0.5 mm
2
or more for the
places where misoperation may occur from the noise.
7 Switch setting
¶ How to set the address switch
When connecting to the adapter kit, no need to set the
address switch. (When shipped from factory, setting is 0.)
When connecting to S-DDC, set address switches of
whole connected AMY adapters, as follows.
TB2
D1
5
6
Potential free contact
1852_M_I
TB2
P1
7
8
P2
10
9
P3
12
11
Pulse
input 1
Pulse
input 2
Pulse
input 3
1865_M_I
Add.
Switch setting
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
1 2 3 4 5
OFF
6 7 8
2
1 2 3 4 5
OFF
6 7 8
3
1 2 3 4 5
OFF
6 7 8
4
1 2 3 4 5
OFF
6 7 8
5
1 2 3 4 5
OFF
6 7 8
6
1 2 3 4 5
OFF
6 7 8
7
1 2 3 4 5
OFF
6 7 8
1 2 3 4 5
OFF
6 7 8
9
8
1 2 3 4 5
OFF
6 7 8
1
12345678
OFF
2
12345678
OFF
3
12345678
OFF
4
12345678
OFF
5
12345678
OFF
0
12345678
OFF
1 2 3 4 5
OFF
SW1 SW2
OFF
ON
6 7 8
Address
setting
(1-9)
Address
setting
for 10 or
more address
setting
(10-31)
Pulse counter setting switch
(Turn on this switch when
used for pulse counter only)
ON
OFF
: When using pulse counter
: Usual use
Not defined.
Keep these
switches
always OFF
Test Mode:
Use this switch
always OFF
0
1864_M_I
Add.
Switch setting
No.
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
(When shipped from factory, setting is 0.)
1 2 3 4 5 6 7 8
7
OFF
1 2 3 4 5 6 7 8
8
OFF
1 2 3 4 5 6 7 8
9
OFF
1
12345678
OFF
2
12345678
OFF
3
12345678
OFF
4
12345678
OFF
7
12345678
OFF
9
12345678
OFF
0
12345678
OFF
5
12345678
OFF
6
12345678
OFF
8
12345678
OFF
1
12345678
OFF
0
12345678
OFF
6
12345678
OFF