How to resolve LAN Time Out Error on SATO CT 408i?
If you encounter a LAN Time Out Error on your SATO Printer, check the interface card and all associated connections to and from it. Replace the card if necessary.
Why is the LED field illuminated but there is no display on my SATO CT 408i?
If the LED field is illuminated but there is no display on your SATO Printer, ensure the cable is properly connected and check/replace the power supply. Also, adjust the display potentiometer as required.
How to fix 'Head Not Latched' error on SATO CT 408i?
To resolve a 'Head Not Latched' error on your SATO Printer, securely latch the print head and ensure that the top cover is closed properly.
What does 'Ribbon End' mean on my SATO Printer?
If your SATO Printer indicates 'Ribbon End', check the ribbon loading and load a new ribbon roll if necessary. This applies to TT models only.
Why is the media meandering in my SATO Printer?
If the media is meandering in your SATO Printer, ensure correct loading of the media. Adjust the media guides as required. An unbalanced print head may also cause this issue, so adjust it accordingly. Replace worn rollers if necessary.
How to fix uneven print darkness on my SATO CT 408i?
Uneven print darkness on your SATO Printer can be caused by an unbalanced print head (adjust head balance), worn rollers (replace rollers as required), or a dirty print head (clean print head).
Why is there no printed image from my SATO Printer?
If your SATO Printer is not printing any image, ensure the print head wiring harness is connected on each end. Replace the fuse and test the power supply if there's no voltage output, replacing as required. A defective print head or damaged electronics (circuit board) may also be the cause, requiring replacement. Troubleshoot the interface or ensure the correct data stream.
Why is my SATO Printer printing labels in the wrong position?
Incorrect label positioning on your SATO Printer can be caused by several factors. Ensure the correct printer configuration is set for the label sensor. Adjust the sensor sensitivity as required. Verify that the correct data stream is being sent to the printer, and adjust the offset settings as needed.
How to resolve image voids on my SATO CT 408i?
Image voids on your SATO Printer can result from a dirty or damaged print head (clean or replace it), damaged electronics (replace the circuit board), or damaged/worn rollers (replace the rollers). Poor label quality can also cause this, so use higher quality media. Additionally, ensure the ribbon stock and media are properly matched, consulting with your media supplier and using only SATO-certified media.
Why does my SATO CT 408i create a blank label?
If your SATO Printer is creating blank labels, ensure the correct data stream is being sent. Also, verify that the printer configuration has the correct label sensor selected. Power off the printer and ensure the print head is properly connected. If the issue persists, the print head or main circuit board may be defective and require replacement.
General| Print Resolution | 203 dpi |
|---|---|
| Print Speed | Up to 6 ips |
| Print Method | Thermal Transfer / Direct Thermal |
| Max Print Width | 4.09 inches (104 mm) |
| Media Width | 22 to 118 mm |
| Media Thickness | 0.06 to 0.19 mm |
| Connectivity | USB, Serial, Parallel |
| Memory | 16 MB RAM |
| Weight | 4.3 kg |
| Supported Barcode Types | Code 39, Code 128, UPC-A, UPC-E, EAN-8, EAN-13, ITF, Codabar, MSI, PDF417, Data Matrix, QR Code, MaxiCode |
| Supported Media Types | Roll, Fanfold |
| Operating Temperature | 41°F to 104°F (5°C to 40°C) |
Details print method, speed, resolution, and maximum print width/length.
Lists supported linear and two-dimensional barcode symbologies.
Combines general, electrical, and placement safety guidelines to prevent injury and damage.
Describes different operational modes like Continuous, Tear-off, Cutter, and Dispense.
Explains the LEDs (Power, Error, Online) and buttons (Online, Feed) on the printer's front panel.
Details the DIP switch, potentiometers, and LED error status display on the configuration panel.
Explains the function of DIP switches for paper handling, print method, and modes.
Lists various operational modes and their invocation sequences using buttons and DIP switches.
Guides on using a potentiometer to adjust the label stop position.
Provides a table of error conditions, display codes, buzzers, and corrective actions.
Offers checklists for troubleshooting Parallel, RS232, USB, LAN, Wireless, and Centronics interfaces.
Details methods for cleaning the printer, including print head, platen, and rollers.
Covers adjusting print quality, including print darkness and print speed.
Provides step-by-step instructions for cleaning the print head, platen, and rollers.
To Next Page
